Not applicable
May 22, 2013
05:00 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
May 22, 2013
05:00 AM
Hi, I''m working on a project using the C167CS micro controller and i want to program it but i don't know how to do this!
If i use the ulink2, how can i connect the pins to its connector?
which pins will be used ?
please guide me
thanks
If i use the ulink2, how can i connect the pins to its connector?
which pins will be used ?
please guide me
thanks
Labels
- Tags:
- IFX
8 Replies
May 22, 2013
10:19 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
May 22, 2013
10:19 PM
Hi Carlos,
The C167CS microcontroller is a Mask ROM based device. It does not have any programming or debug interface so the Ulink2 can not be used with this part.
The C167 parts are quite old now and have been replaced by the XC2000 16-bit family. You can find information about the XC2000 family at www.infineon.com/XC2000
Regards,
Chris
The C167CS microcontroller is a Mask ROM based device. It does not have any programming or debug interface so the Ulink2 can not be used with this part.
The C167 parts are quite old now and have been replaced by the XC2000 16-bit family. You can find information about the XC2000 family at www.infineon.com/XC2000
Regards,
Chris
Mar 16, 2015
11:46 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Mar 16, 2015
11:46 PM
hi Chris66.
I have this problem too. But i want using SAK-C167CS-LM and put external flash in my circuit.
How can i program external flash in Circuit?in your opinion i must eject flash and program,then put in circuit every time?
have special interface for this work?
I don't want change in hardware.
please help.
thanks.
I have this problem too. But i want using SAK-C167CS-LM and put external flash in my circuit.
How can i program external flash in Circuit?in your opinion i must eject flash and program,then put in circuit every time?
have special interface for this work?
I don't want change in hardware.
please help.
thanks.
Not applicable
Mar 29, 2015
08:30 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Mar 29, 2015
08:30 PM
Hi hemn,
As mentioned by Chris, this device is very old and not much information is available.
I would suggest you look through the application note C16xCx - Programming an external flash memory via the CAN bus (ap1607510_.pdf) and use that as the reference for your implementation.
As mentioned by Chris, this device is very old and not much information is available.
I would suggest you look through the application note C16xCx - Programming an external flash memory via the CAN bus (ap1607510_.pdf) and use that as the reference for your implementation.
Mar 31, 2015
12:52 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Mar 31, 2015
12:52 AM
Hi Jackson.
Thank you.:)
Thank you.:)
Jun 21, 2015
12:32 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jun 21, 2015
12:32 AM
Hi jackson.
I still work on the C167CS-LM.
solved programming problem.
I've made simple board to C167CS-LM.a AM29F400BB-90ns flash used for external flash.
i use FlasHit9 software in bootstrap mode for programming.when connect a board and read CPU info,that is Ok, read but Does not recognize external flash.
what is wrong?!please can help me?thank you.:(
Circuit Diagram and register setting is:
http://s000.tinyupload.com/?file_id=47320254101938365208
I still work on the C167CS-LM.
solved programming problem.
I've made simple board to C167CS-LM.a AM29F400BB-90ns flash used for external flash.
i use FlasHit9 software in bootstrap mode for programming.when connect a board and read CPU info,that is Ok, read but Does not recognize external flash.
what is wrong?!please can help me?thank you.:(
Circuit Diagram and register setting is:
http://s000.tinyupload.com/?file_id=47320254101938365208
Nov 16, 2015
06:23 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nov 16, 2015
06:23 AM
Hi.I want enable the RTC timer in C167CS-LM.in Simulator of the keil this Timer work fine and can use the interrupt, but in real world this timer do not count! what is problem? the RTC registers need to unlock to change?
to setting of register i use the Dave Code Generator.
Setting of register:
T14= 0xFEC8 ;
T14REL = 0xFEC8 ; // load RTC reload register
RTC_vReset();
/// -----------------------------------------------------------------------
/// Configuration of the used RTC Interrupts:
/// -----------------------------------------------------------------------
/// - RTC_PLL_OWD service request node configuration:
/// - RTC_PLL_OWD interrupt priority level (ILVL) = 9
/// - RTC_PLL_OWD interrupt group level (GLVL) = 1
XP3IC=0x0065;
ISNC= 0x0002; // load interrupt sub node register for
interrupt Function:
void RTC_viRTC(void) interrupt XP3INT=0x43
{
// USER CODE BEGIN (RTC,2)
// USER CODE END
if(ISNC_RTCIR) //if RTC interrupt
{
ISNC_RTCIR = 0;
IO_vTogglePin(IO_P3_1);
} //end of RTC interrupt
if(XP3IC_XP3IR)
{
XP3IC_XP3IR =0;
}
} // End of function RTC_viRTC
thanks .
to setting of register i use the Dave Code Generator.
Setting of register:
T14= 0xFEC8 ;
T14REL = 0xFEC8 ; // load RTC reload register
RTC_vReset();
/// -----------------------------------------------------------------------
/// Configuration of the used RTC Interrupts:
/// -----------------------------------------------------------------------
/// - RTC_PLL_OWD service request node configuration:
/// - RTC_PLL_OWD interrupt priority level (ILVL) = 9
/// - RTC_PLL_OWD interrupt group level (GLVL) = 1
XP3IC=0x0065;
ISNC= 0x0002; // load interrupt sub node register for
interrupt Function:
void RTC_viRTC(void) interrupt XP3INT=0x43
{
// USER CODE BEGIN (RTC,2)
// USER CODE END
if(ISNC_RTCIR) //if RTC interrupt
{
ISNC_RTCIR = 0;
IO_vTogglePin(IO_P3_1);
} //end of RTC interrupt
if(XP3IC_XP3IR)
{
XP3IC_XP3IR =0;
}
} // End of function RTC_viRTC
thanks .
Not applicable
Oct 10, 2016
08:22 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Oct 10, 2016
08:22 AM
I have similar problem and I'm using Infineon Minimon for read.
May 27, 2021
08:39 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
May 27, 2021
08:39 AM
hemn wrote:
Hi jackson.
I still work on the C167CS-LM.
solved programming problem.
I've made simple board to C167CS-LM.a AM29F400BB-90ns flash used for external flash.
i use FlasHit9 software in bootstrap mode for programming.when connect a board and read CPU info,that is Ok, read but Does not recognize external flash.
what is wrong?!please can help me?thank you.:(
Circuit Diagram and register setting is:
http://s000.tinyupload.com/?file_id=47320254101938365208
Hi,
can you tell me which hardware is required to program C167CS-LM.
I also need it urgently.
Thanks