Jun 06, 2019
02:49 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jun 06, 2019
02:49 AM
Hi,
I'd need some support about the Arduino Software usage on this shield.
Provided examples just offer the code for on, spin and stop the motor but anything else. Could anybody give me some hints? (i.e. Examples for changing parameters for HALL mode, spin direction and so on)
Thanks in advance,
gaston
I'd need some support about the Arduino Software usage on this shield.
Provided examples just offer the code for on, spin and stop the motor but anything else. Could anybody give me some hints? (i.e. Examples for changing parameters for HALL mode, spin direction and so on)
Thanks in advance,
gaston
Labels
- Tags:
- IFX
3 Replies
Aug 12, 2019
04:42 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Aug 12, 2019
04:42 AM
Embarrassing support. The worst I've seen in +20 years of experience.
gaston
gaston
Aug 14, 2019
01:17 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Aug 14, 2019
01:17 AM
Hello Gaston,
We are very sorry for your long waiting time. In any cases you can contact our technical assistance center: https://www.infineon.com/cms/en/about-infineon/company/contacts/product-support-form/?redirId=56193
We are working on more information how to work with the Arduino Shield.
Best,
Fiz
We are very sorry for your long waiting time. In any cases you can contact our technical assistance center: https://www.infineon.com/cms/en/about-infineon/company/contacts/product-support-form/?redirId=56193
We are working on more information how to work with the Arduino Shield.
Best,
Fiz
Aug 19, 2019
05:13 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Aug 19, 2019
05:13 AM
Hello Gaston,
the spin orientation can be changed by putting a negative argument for: shields->setMotorSpeed(-XXXX).
To set the HALL parameter, you will have to install the tool-chain for our Embedded Power ICs' (https://www.infineon.com/cms/en/product/microcontroller/embedded-power-ics-system-on-chip-/?redirId=...),
but you can skip the installation of the Infineon Toolbox.
You will need to install Config Wizard Version 1.X (https://infineoncommunity.com/2018Aug_GLOB_ATV_GATED_Config_Wizard_Id1003).
In addition to the software tool-chain you would need a Segger J-Link debugger to flash the TLE9879 over SWD.
If you need further assistance let us know.
Best,
Fiz
the spin orientation can be changed by putting a negative argument for: shields->setMotorSpeed(-XXXX).
To set the HALL parameter, you will have to install the tool-chain for our Embedded Power ICs' (https://www.infineon.com/cms/en/product/microcontroller/embedded-power-ics-system-on-chip-/?redirId=...),
but you can skip the installation of the Infineon Toolbox.
You will need to install Config Wizard Version 1.X (https://infineoncommunity.com/2018Aug_GLOB_ATV_GATED_Config_Wizard_Id1003).
In addition to the software tool-chain you would need a Segger J-Link debugger to flash the TLE9879 over SWD.
If you need further assistance let us know.
Best,
Fiz