infineon4engineers Facebook

infineon@google+ Google+

infineon@linkedin linkedin

infineon4engi@twitter twitter

infineon@youtube youtube

+ Reply to Thread
Results 1 to 2 of 2

Thread: Several questions about using iMOTION

  1. #1
    New Member New Member zhangjh is on a distinguished road
    Join Date
    Nov 2018

    Several questions about using iMOTION

    The following questions are asked:

    First, after the program is written to the development board, how to operate the motor without opening the software can be achieved.

    The value I entered in TargetSpeed, how to download it to the core, and how can I run the electricity without turning on MCEdesigner, and achieve the performance set in MCE designer. (There is a cap of 32767 for TargetSpeed, what can I do if I still improve the speed?

    Two, how to view the program's C language code.

    Three, the circuit diagrams of the two development boards can be downloaded.

    Four, about MATLAB simulation whether there is any information, I want to do some simulation.

    Five, in addition to programming with imotion, MCK099 chips can also be programmed to write.

    Sixth, if my motor winding is triangular connection, is the resistance, inductance and KE measured first according to Y connection?

    Thank you. May I ask the Engineer for help?

  2. #2
    New Member New Member
    Infineon Employee
    Infineon Employee
    berbra is on a distinguished road
    Join Date
    May 2017
    First: The IRMCK099 combines the iMOTION™ motor control engine (MCE) with all peripherals required to realize a complete variable speed drive (for permanent magnet motors).
    The steps to develop a motor control are MCE(Tiny)Wizard -> MCEDesigner -> MCEProgrammer.
    Once you have developped the MCE for one or more (up to 31 Motors) motor characteristics you will do the one time programming (OTP) of the device. You will develop things like ramp up, speed, and ramp down of the motor, Start, Stop etc. either as standalone, configuration or with human interface using for instance the GPIOs. You will check the result by programming the SRAM of the device with the help of MCETOOLV2 (start MCEProgrammer). When finished you can program to OTP. Using the internal SRAM allows an unlimited number of development cycles, while the MCEProgrammer is used to write the firmware and final parameter set into the OTP memory.

    Two: For devices having only a Motor Control Engine, without microcontroller, there is only a download firmware binary. No software source code available. Motor parameter sets are downloaded to device as well as mentioned in "First".

    Three: Download the installer file from the TAB Tools&Software via the EvalBoards webpage. After installation you will find the circuit diagram in the folder ../documents/iMotion/<Board>/hardware.Four: See your thread

    Four: Answered in your thread here.

    Five: ??.

    Sixth: When measuring the winding resistance between two phase terminals devide the result by two to get the per phase resistance value for both Y or delta connected motors. Measuring the winding inductance you will always read twice the per phase inductance. See TinyWizard(MCEWizard) Questions about the Motor Parameters.
    The views expressed here are my personal opinions, have not been reviewed or authorized by Infineon and do not necessarily represent the views of Infineon.

+ Reply to Thread

All content and materials on this site are provided “as is“. Infineon makes no warranties or representations with regard to this content and these materials of any kind, whether express or implied, including without limitation, warranties or representations of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, whether express or implied, is granted by Infineon. Use of the information on this site may require a license from a third party, or a license from Infineon.

Infineon accepts no liability for the content and materials on this site being accurate, complete or up- to-date or for the contents of external links. Infineon distances itself expressly from the contents of the linked pages, over the structure of which Infineon has no control.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Usage Terms of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Usage Terms of this site. Infineon reserves the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.