Sep 28, 2018
10:40 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 28, 2018
10:40 PM
Hi All,
I use TLE987x to drive my motor, when the current up to 25A, it seems that the driver output current is not enough, and can't keep the rotation any more and stop.But I checked the registers, there is no OC error.
I'm not sure whether the driver output current is enough. How to solve this problem?
I use TLE987x to drive my motor, when the current up to 25A, it seems that the driver output current is not enough, and can't keep the rotation any more and stop.But I checked the registers, there is no OC error.
I'm not sure whether the driver output current is enough. How to solve this problem?
Labels
- Tags:
- IFX
- tle987x current
5 Replies
Sep 29, 2018
11:04 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 29, 2018
11:04 AM
Hi Jacko,
what types of MOS-FETs are you using? The TLE987x has a maximum total charge driver capability of 100 nC. The IC is able to drive motors up 1kW. Maybe your power - supply has a voltage drop? Could you please send a scope plot of all supply voltages?
what types of MOS-FETs are you using? The TLE987x has a maximum total charge driver capability of 100 nC. The IC is able to drive motors up 1kW. Maybe your power - supply has a voltage drop? Could you please send a scope plot of all supply voltages?
Sep 29, 2018
05:37 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 29, 2018
05:37 PM
Lykaon wrote:
Hi Jacko,
what types of MOS-FETs are you using? The TLE987x has a maximum total charge driver capability of 100 nC. The IC is able to drive motors up 1kW. Maybe your power - supply has a voltage drop? Could you please send a scope plot of all supply voltages?
Hi Lykaon,
The QG(total) of MOSFETS is 145nC, QGS is 35.7nC, QGD is 48.2nC. The voltage not drop, I sure. My software is base on BLDC_BC_BEMF_EXAMPLE_TLE987X. The rotation speed can up to my setting speed when unloading. I use another board(not use TLE987x), the same power source, same MOSFETS, same voltage, it can up to 60A. In addition, the voltage is 13V.
Sep 30, 2018
10:54 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 30, 2018
10:54 PM
Hi Jacko,
you can modify the Icharge and Idischarge settings, are you aware of this? Please increase the current and try again
you can modify the Icharge and Idischarge settings, are you aware of this? Please increase the current and try again
Oct 01, 2018
01:23 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Oct 01, 2018
01:23 AM
...in addition please make a scope shot of your motor phase (SHx), this will help us to understand the behaviour.
Oct 04, 2018
01:42 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Oct 04, 2018
01:42 AM
Lykaon wrote:
...in addition please make a scope shot of your motor phase (SHx), this will help us to understand the behaviour.
Hi Lykaon,
I modified the Icharge and Idischarge settings, and increase them, but no effect.
I didn't catch the shot of SHx when problem occur, but before problem occur. Holp this can help you to analyze.
Anyway, it seems that the BEMF is not correct. Emo_StopMotor() had been executed.
case EMO_MOTOR_STATE_RUN:
{
if (Emo_Bemf.timeoutcounter > (3 * Emo_Bemf.difftimeout))
{
Emo_StopMotor();
}
} break;
Thanks!