No BMI Button In Dave4

Tip / Sign in to post questions, reply, level up, and achieve exciting badges. Know more

cross mob
Not applicable
Sorry,

I'm new with Dave4 but I can't get the BMI-Button.

Thank you for help!

Bernd2489.attach
0 Likes
9 Replies
WoS
Employee
Employee
First solution authored
Maybe it is just disabled? You may try following:
Select in Eclipse menu: "Window" -> "Customize Perspective..."
From this dialog, select "Tool Bar Visibility" and click on "toolbar", then click the checkbox left of "command":

4919.attach

Hope it helps...
0 Likes
jferreira
Employee
Employee
10 sign-ins 5 sign-ins First like received
Hi

The BMI tool is only available if the current active project is for XMC1000 family.
If you need a standalone tool for modifying the BMI, have a look to XMC Flasher

Regards,
Jesus
0 Likes
Not applicable
Thank you WoS!
There is the BMI-Button if I use my XMC1200 bootkid.

Thank you Jesus!
If I use my XMC1200 bootkid the XMC flasher works well.
But if I use my XMC4500-kid the BMI button is disabled!

Thank
Regards,
Bernd
0 Likes
Not applicable
Hi

I have recently updated DAVE to v4.3.2 and since then the BMI tool throws an error "Unable to find SEGGER J-Link path". This works fine on v4.2.8 though.
0 Likes
Not applicable
Hi,

I'm trying to connect to XMC4200Q48 using the XMC-Jlink,
I cant get it to work, and the next Error shoos:
Could not connect to target. Please check if target is powered and if ribbon cable is plugged properly.

I also tried the XMCFlasher, I cant get it to erase the target.
the target connected to the Jlink with the 10 pin header:
4923.attach

Thanks.
0 Likes
ipek
Level 4
Level 4
25 replies posted 10 replies posted 10 questions asked
mavula wrote:
Hi

I have recently updated DAVE to v4.3.2 and since then the BMI tool throws an error "Unable to find SEGGER J-Link path". This works fine on v4.2.8 though.


Hi,
Maybe you should add your SEGGER J-Link path. Sometimes It cannot find by its own.
You can check from Window->Preferences->Run/Debug->Segger J-Link
0 Likes
ipek
Level 4
Level 4
25 replies posted 10 replies posted 10 questions asked
jferreira wrote:
Hi

The BMI tool is only available if the current active project is for XMC1000 family.
If you need a standalone tool for modifying the BMI, have a look to XMC Flasher

Regards,
Jesus


Hi Jesus,

That XMCFlaser link is not available now.
Can you update ?
0 Likes
jferreira
Employee
Employee
10 sign-ins 5 sign-ins First like received
Hi,

XMCFlasher can be installed using Infineon Toolbox, https://www.infineon.com/cms/en/tools/landing/infineontoolbox.html
Additionally you can change the BMI using the J-Link Commander. Use the getbmi/setbmi commands (with care), https://wiki.segger.com/Infineon_XMC1000

Regards,
Jesus
0 Likes
ipek
Level 4
Level 4
25 replies posted 10 replies posted 10 questions asked
Hi Jesus,

I read this( https://wiki.segger.com/Infineon_XMC1000) and didn't saw anything about set/get BMI.
I tried to do this with JLink Commander already.
When I opened the program and connected to the XMC1400 MCU, I printed the command list and there were no get/set BMI command in there..
As a matter of fact I could only connect to the board when it is in SWD0 mode. I couldn't connect when it is in ASC BSL mode.
I think I am doing something wrong but don't know where to look for the right answer.
0 Likes