Not applicable
Nov 03, 2016
12:43 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nov 03, 2016
12:43 PM
Hey guys,
I'm trying to read the data coming from the Infineon 3D magnetic sensor in C#/C++.
Currently I'm sucesssfully connecting to the COM Port using the C# SerialPort class but I don't know how to exchange data between the c#-application and the sensor.
Does someone have an example or can guide me into the right direction for the way of achieving this?
Thanks in advance
Tim
I'm trying to read the data coming from the Infineon 3D magnetic sensor in C#/C++.
Currently I'm sucesssfully connecting to the COM Port using the C# SerialPort class but I don't know how to exchange data between the c#-application and the sensor.
Does someone have an example or can guide me into the right direction for the way of achieving this?
Thanks in advance
Tim
6 Replies
Nov 15, 2016
12:35 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nov 15, 2016
12:35 AM
Hi,
Which board are you using? 3D Magnetic Sensor 2GO?
Regards,
Jesus
Which board are you using? 3D Magnetic Sensor 2GO?
Regards,
Jesus
Not applicable
Sep 06, 2017
08:12 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 06, 2017
08:12 AM
jferreira wrote:
Hi,
Which board are you using? 3D Magnetic Sensor 2GO?
Regards,
Jesus
Hello,
I'm trying too to connect to the sensor via USB and C#, but I have no idea how to start and stop the device, and how to decode the data.
Some help would be hugely appreciated,
Marco Ciarrocca
Sep 06, 2017
10:32 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 06, 2017
10:32 AM
Do you use the official firmware or your customized firmware.
If you develop the firmware by yourself, you could define the protocol as you like.
If you will use the official firmware, then some reverse engineering is expected. The official firmware don't have source code released with it.
If you develop the firmware by yourself, you could define the protocol as you like.
If you will use the official firmware, then some reverse engineering is expected. The official firmware don't have source code released with it.
Not applicable
Sep 07, 2017
12:01 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 07, 2017
12:01 AM
I am currently using the official firmware, and I managed to retrieve the data, but I can't figure out how to decode the bytes I receive. They have random length and have little constancy between them
Sep 07, 2017
10:12 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 07, 2017
10:12 AM
I have tried to request the source code of the official firmware. But Infineon refused to provide it.
Now I am using my customized firmware. It's not very difficult to write the driver for the magnetic sensor. You should have a try.
Now I am using my customized firmware. It's not very difficult to write the driver for the magnetic sensor. You should have a try.
Not applicable
Sep 11, 2017
08:27 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 11, 2017
08:27 AM
Yes, I am now trying too to program my own firmware...