Not applicable
Feb 17, 2016
07:05 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 17, 2016
07:05 AM
Hi everybody,
I'm a very beginner with Dave. I'm Using Dave 3.1.10 with an XMC 4500.
The problem is that I can't add new Apps into an existing project which already contains applications.
I checked path settings and if libraries are installed. Everything seems to be ok,but the App Selection View is empty.
Can anybody help me with this trouble?
Thanks in advance for any advice.
Best regards,
Andrea.
I'm a very beginner with Dave. I'm Using Dave 3.1.10 with an XMC 4500.
The problem is that I can't add new Apps into an existing project which already contains applications.
I checked path settings and if libraries are installed. Everything seems to be ok,but the App Selection View is empty.
Can anybody help me with this trouble?
Thanks in advance for any advice.
Best regards,
Andrea.
4 Replies
Not applicable
Feb 17, 2016
06:59 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 17, 2016
06:59 PM
HI Andrea,
Did you create a DAVE CE project or a Simple Main Project? You will need to create a DAVE CE project to install APPs to your project.
If you are just starting out using DAVE, I strongly recommend you to install DAVE v4.2.2. ( http://www.infineon.com/dave )
Link to "Quick start to DAVE": http://www.infineon.com/dgdl/Infineon-DAVE_Quick_Start-GS-v02_00-EN.pdf?fileId=5546d4624cb7f111014d0...
Regards,
Daryl
Did you create a DAVE CE project or a Simple Main Project? You will need to create a DAVE CE project to install APPs to your project.
If you are just starting out using DAVE, I strongly recommend you to install DAVE v4.2.2. ( http://www.infineon.com/dave )
Link to "Quick start to DAVE": http://www.infineon.com/dgdl/Infineon-DAVE_Quick_Start-GS-v02_00-EN.pdf?fileId=5546d4624cb7f111014d0...
Regards,
Daryl
Not applicable
Feb 18, 2016
12:08 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 18, 2016
12:08 AM
Thank you Daryl for your reply.
Yes, I created a CE Project.
The fact is that I need to use Dave 3.1 to develope my project.
How can I add apps on 3.1 version? Tobe sure I'm following the right procedure...
Yes, I created a CE Project.
The fact is that I need to use Dave 3.1 to develope my project.
How can I add apps on 3.1 version? Tobe sure I'm following the right procedure...
Not applicable
Feb 18, 2016
06:44 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 18, 2016
06:44 AM
I followed your advice and I downloaded DAVE v4.2.2.
I was able to insert Apps and set pins.
But when I use Debug mode I get an error in which is reported the inability to launch "arm-none-eabi-gdb". May it be due to my J-Link?
I was able to insert Apps and set pins.
But when I use Debug mode I get an error in which is reported the inability to launch "arm-none-eabi-gdb". May it be due to my J-Link?
Not applicable
Feb 18, 2016
09:58 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 18, 2016
09:58 PM
HI Andrea,
Were you able to generate code and compile the project?
Can you check your debug configurations as in the attached pic.
Regards,
Daryl
Were you able to generate code and compile the project?
Can you check your debug configurations as in the attached pic.
Regards,
Daryl