Not applicable
Dec 14, 2015
10:43 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dec 14, 2015
10:43 PM
Hi,
i am working on ASC_BSL. i want to flash xmc4500 using ASC_BSL , after refering the tooling guide i sent 0x00 to the xmc4500 using ASC_BSL and i expected 0x5D from it but it won't respond. where might be the error???
Thanks and Regards.
Harshan
i am working on ASC_BSL. i want to flash xmc4500 using ASC_BSL , after refering the tooling guide i sent 0x00 to the xmc4500 using ASC_BSL and i expected 0x5D from it but it won't respond. where might be the error???
Thanks and Regards.
Harshan
6 Replies
Dec 23, 2015
12:33 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dec 23, 2015
12:33 AM
Hi harshan,
Did you setup the TMS and TCK correctly? This configuration is to let the MCU to enter into ASC_BSL mode.
Please ensure that your hardware is working by doing a flash programming using the Infineon Memtool. (see below link) If this part is working then we have to look into the PC software. And it is also good that you have an oscilloscope connected to the ASC Tx Rx such that you are sure that there is communication going on.
http://www.infineonforums.com/threads/2066-XMC_HOT-XMC4500-How-to-do-flash-programming-using-Infineo...
Best Regards
Travis
Did you setup the TMS and TCK correctly? This configuration is to let the MCU to enter into ASC_BSL mode.
Please ensure that your hardware is working by doing a flash programming using the Infineon Memtool. (see below link) If this part is working then we have to look into the PC software. And it is also good that you have an oscilloscope connected to the ASC Tx Rx such that you are sure that there is communication going on.
http://www.infineonforums.com/threads/2066-XMC_HOT-XMC4500-How-to-do-flash-programming-using-Infineo...
Best Regards
Travis
Not applicable
Jan 04, 2016
09:02 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jan 04, 2016
09:02 PM
Thanks for Quick Reply,
i am using xmc4500 relax kit for it there is no boot switch exist. shall i connect TMS and TCK to GND manually or any alternative Circuits are needed???
i am using xmc4500 relax kit for it there is no boot switch exist. shall i connect TMS and TCK to GND manually or any alternative Circuits are needed???
Jan 05, 2016
06:47 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jan 05, 2016
06:47 PM
harshan wrote:
Thanks for Quick Reply,
i am using xmc4500 relax kit for it there is no boot switch exist. shall i connect TMS and TCK to GND manually or any alternative Circuits are needed???
Yes, manual connection should work as the startup software is looking for this configuration to enter into ASC_BSL.
Not applicable
Jan 19, 2016
01:31 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jan 19, 2016
01:31 AM
Hi Travis,
With reference to your previous reply I had connected TMS and TCK to Ground Manually by Ensuring the target to enter ASC_BSL mode,
But after the Hardware Setup I tried to Communicate with Terminal by sending 0x00 By Expecting a response 0x5D.
There is No Response from the Target. let me know is there any steps I am missing To Get Into ASC_BSL Mode.
please let me know any further information required to you regarding this post.
Thanks and Regards,
Harshan
With reference to your previous reply I had connected TMS and TCK to Ground Manually by Ensuring the target to enter ASC_BSL mode,
But after the Hardware Setup I tried to Communicate with Terminal by sending 0x00 By Expecting a response 0x5D.
There is No Response from the Target. let me know is there any steps I am missing To Get Into ASC_BSL Mode.
please let me know any further information required to you regarding this post.
Thanks and Regards,
Harshan
Jan 22, 2016
12:21 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jan 22, 2016
12:21 AM
harshan wrote:
Hi Travis,
With reference to your previous reply I had connected TMS and TCK to Ground Manually by Ensuring the target to enter ASC_BSL mode,
But after the Hardware Setup I tried to Communicate with Terminal by sending 0x00 By Expecting a response 0x5D.
There is No Response from the Target. let me know is there any steps I am missing To Get Into ASC_BSL Mode.
please let me know any further information required to you regarding this post.
Thanks and Regards,
Harshan
Hi,
You can check more in detail on the user manual of the XMC4500 Hex board.
Not applicable
Jan 23, 2016
01:51 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jan 23, 2016
01:51 AM
Thanks for reply travis,
without any hardware changes by setting SWCON to ASCBSL and then if the set Reset Request bit in AIRCR Register Can i Switch to ASCBSL mode???
Thanks and Regards,
Harshan
without any hardware changes by setting SWCON to ASCBSL and then if the set Reset Request bit in AIRCR Register Can i Switch to ASCBSL mode???
Thanks and Regards,
Harshan