Feb 25, 2013
01:47 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 25, 2013
01:47 AM
Hello,
I wonder how to operate the firmware download to the XMC4500 via the ASC Bootloader using the MemTool. What are the MemTool settings for using the ASC Bootlaoder instead of the JTAG link?
Best wishes
Helmut
I wonder how to operate the firmware download to the XMC4500 via the ASC Bootloader using the MemTool. What are the MemTool settings for using the ASC Bootlaoder instead of the JTAG link?
Best wishes
Helmut
10 Replies
Feb 25, 2013
06:07 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 25, 2013
06:07 AM
Hello Helmut,
Memtool uses the UART BSL in BootROM of the chip, in detail USIC0 channel0 on pin P1.4 and P1.5. What you need to do first is to bring the device into BSL mode. This is done with the DIP switch on the Hexagon Board (setting up TMS and TCK pins). Then you need a serial port connected to the pins P1.4 and P1.5. Select in Memtool the "Infineon XMC4500 StarterKit XMC4500 (BSL/ASC)" as the Target. With this setting Memtool will work.
Regards
Memtool uses the UART BSL in BootROM of the chip, in detail USIC0 channel0 on pin P1.4 and P1.5. What you need to do first is to bring the device into BSL mode. This is done with the DIP switch on the Hexagon Board (setting up TMS and TCK pins). Then you need a serial port connected to the pins P1.4 and P1.5. Select in Memtool the "Infineon XMC4500 StarterKit XMC4500 (BSL/ASC)" as the Target. With this setting Memtool will work.
Regards
Feb 28, 2013
06:06 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 28, 2013
06:06 AM
Hello Ron,
At "Select Target Configuration" in MenTool I can browse only to "Infineon XMC4500 starterkit XMC4500 (DAS)" How can i get the .cfg file for (BSL/ASC)?
I am using MemTool Version 4.05.04
Best wishes
Helmut
At "Select Target Configuration" in MenTool I can browse only to "Infineon XMC4500 starterkit XMC4500 (DAS)" How can i get the .cfg file for (BSL/ASC)?
I am using MemTool Version 4.05.04
Best wishes
Helmut
Feb 28, 2013
06:33 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 28, 2013
06:33 AM
Hello Ron,
I upgraded to MemTool Version 4.05.05, which includes "Infineon XMC4500 StarterKit XMC4500 (BSL/ASC)".
Best wishes
Helmut
I upgraded to MemTool Version 4.05.05, which includes "Infineon XMC4500 StarterKit XMC4500 (BSL/ASC)".
Best wishes
Helmut
Feb 28, 2013
04:54 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Feb 28, 2013
04:54 PM
Hello Ron,
I succeeded in a first contact with the XMC4500 ASC bootloader from the MemTool. But the communication broke after transmitting the length of the monitor image to the XMC4500. The SMC4500 replied with 0x81 instead of 0x01 and the MemTool terminated the communication.
The red characters are sent from the MemTool and the blue characters are sent from the XMC4500.
Best wishes
Helmut
I succeeded in a first contact with the XMC4500 ASC bootloader from the MemTool. But the communication broke after transmitting the length of the monitor image to the XMC4500. The SMC4500 replied with 0x81 instead of 0x01 and the MemTool terminated the communication.
The red characters are sent from the MemTool and the blue characters are sent from the XMC4500.
Best wishes
Helmut
Mar 01, 2013
12:17 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Mar 01, 2013
12:17 AM
Hello Helmut,
Can you check please what Step of the XMC4500 do you have. Please have a look to the device, is there a AA13 printed on? In case of that we need to exchange the device to AB step.
Just for your Info, in the actual Errata Sheet you find the STARTUP_CM.H001 issue.
Best Regards
Can you check please what Step of the XMC4500 do you have. Please have a look to the device, is there a AA13 printed on? In case of that we need to exchange the device to AB step.
Just for your Info, in the actual Errata Sheet you find the STARTUP_CM.H001 issue.
Best Regards
Mar 01, 2013
03:47 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Mar 01, 2013
03:47 AM
Hello Ron,
on my device is printed "AA13 EES".
How can I get my device exchanged? It is part of the "CPU_45A-V2-" board contained in the Hexagon Application Kit.
Best wishes
Helmut
on my device is printed "AA13 EES".
How can I get my device exchanged? It is part of the "CPU_45A-V2-" board contained in the Hexagon Application Kit.
Best wishes
Helmut
Mar 05, 2013
03:44 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Mar 05, 2013
03:44 AM
Hello Helmut,
no it's the same Board. Are you able to resolder the device if we send you a sample?
Regards
no it's the same Board. Are you able to resolder the device if we send you a sample?
Regards
Nov 20, 2014
08:12 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nov 20, 2014
08:12 AM
Hello Ron,
maybe this old thread is not the best one for my question...
Can I use the current version of the Memtool (4-06.03) to program the Flash of an XMC4400? As our current hardware is currently in production, I do not know the full marking of the XMC yet, "XMC4400-F100F512 AB" is all I know by now.
The XMC4400 does not have the STARTUP_CM.H001 issue mentioned above. BTW: the Memtool allows to set the data rate according to the range specified in the errata sheet. So what is reason you proposed to change the chip?
Thanks, Rudi
maybe this old thread is not the best one for my question...
Can I use the current version of the Memtool (4-06.03) to program the Flash of an XMC4400? As our current hardware is currently in production, I do not know the full marking of the XMC yet, "XMC4400-F100F512 AB" is all I know by now.
The XMC4400 does not have the STARTUP_CM.H001 issue mentioned above. BTW: the Memtool allows to set the data rate according to the range specified in the errata sheet. So what is reason you proposed to change the chip?
Thanks, Rudi
Not applicable
Nov 20, 2014
11:57 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nov 20, 2014
11:57 PM
Hi Rudi,
Yes, you should be able to program the XMC4400 with Memtool.
Yes, you should be able to program the XMC4400 with Memtool.
Nov 21, 2014
12:56 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nov 21, 2014
12:56 AM
Fine: thank you, Jackson