Sep 15, 2015
04:51 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 15, 2015
04:51 AM
8 Replies
Not applicable
Sep 15, 2015
10:16 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 15, 2015
10:16 PM
Hi Rum,
Can you please try to "clean" the project using the following option: Project -> Clean.
Do you still have same error in the console.
Regards,
Daryl
Can you please try to "clean" the project using the following option: Project -> Clean.
Do you still have same error in the console.
Regards,
Daryl
Sep 16, 2015
05:36 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 16, 2015
05:36 AM
Hi,
Of course I get this error. Don't you see, there is some bad character before asterisk.
rm: cannot lstat `*.o': Invalid argument
rum
Of course I get this error. Don't you see, there is some bad character before asterisk.
rm: cannot lstat `*.o': Invalid argument
rum
Not applicable
Sep 16, 2015
11:05 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 16, 2015
11:05 PM
HI Rum,
Try deleting the folder “Debug/Release” and then build/clean again.
Normally, it should work.
Regards,
Daryl
Try deleting the folder “Debug/Release” and then build/clean again.
Normally, it should work.
Regards,
Daryl
Sep 17, 2015
02:20 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 17, 2015
02:20 AM
Hi Daryl,
Deleting doesn't help. Obviously there is problem how the clean rule is generated in makefile. There is something wrong with rm -rf which is trying to run lsat command
If I remove from makefile from clean rule argument *.o problem disappears. Of course makefile is regenerated again at every build....
rum
Deleting doesn't help. Obviously there is problem how the clean rule is generated in makefile. There is something wrong with rm -rf which is trying to run lsat command
If I remove from makefile from clean rule argument *.o problem disappears. Of course makefile is regenerated again at every build....
rum
Sep 18, 2015
02:37 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 18, 2015
02:37 AM
I have to reproduce without success.
Have you installed Cygwin ?
Which are your regional settings ? (control panel -> region and language)
Regards
Oreste
Keyboard
Have you installed Cygwin ?
Which are your regional settings ? (control panel -> region and language)
Regards
Oreste
Keyboard
rum wrote:
Hi,
Of course I get this error. Don't you see, there is some bad character before asterisk.
rm: cannot lstat `*.o': Invalid argument
rum
Sep 18, 2015
08:35 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 18, 2015
08:35 AM
Hi Oreste,
No Cygwin. Italy.
If I setup new simple project problem is not shown. Maybe it is related to number of files in the project.
rum
No Cygwin. Italy.
If I setup new simple project problem is not shown. Maybe it is related to number of files in the project.
rum
Sep 22, 2015
05:05 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sep 22, 2015
05:05 AM
Hi Rum,
we are not able to reproduce the problem but we are going to remove the *.o from clean target.
Very likely this modification will go in the next release (end of Oct).
Regards
Oreste
we are not able to reproduce the problem but we are going to remove the *.o from clean target.
Very likely this modification will go in the next release (end of Oct).
Regards
Oreste
Oct 02, 2015
04:13 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Oct 02, 2015
04:13 AM
i have the same problem with dave 4.1.2 occasionaly - if i press rebuild a couple of times it usually works again normaly