Jul 01, 2014
07:23 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jul 01, 2014
07:23 AM
Hello,
i've made a Dave Project with ADC002 containing 2 channels and a PWMSVM01 App.
The PWMSVM01 App is configured to trigger the DC Link Current Measurement by compare match of one of the CCU slices.
On the other side i've got the ADC002 App, which i've configured to measure Channels A (DC Link Current) and B (DCB voltage) as a sequence of "trigger, AB, trigger, AB".
Unfortunately i'm not able to interconnect the PWMSVM Current Trigger Slice to the ADC Trigger directly, like it's shown in "CCU8 Device Guide V1.0 2013-05" figure 72.
There's no way to connect the "Current Trigger Slice Status" to anything else in the Signal Connection Dialog.
The only way i've got it working, was to put the NVIC002 App between PWMSVM01 and ADC002.
How is the PWMSVM001 supposed to be used for DC Link Current measurement?
Regards
i've made a Dave Project with ADC002 containing 2 channels and a PWMSVM01 App.
The PWMSVM01 App is configured to trigger the DC Link Current Measurement by compare match of one of the CCU slices.
On the other side i've got the ADC002 App, which i've configured to measure Channels A (DC Link Current) and B (DCB voltage) as a sequence of "trigger, AB, trigger, AB".
Unfortunately i'm not able to interconnect the PWMSVM Current Trigger Slice to the ADC Trigger directly, like it's shown in "CCU8 Device Guide V1.0 2013-05" figure 72.
There's no way to connect the "Current Trigger Slice Status" to anything else in the Signal Connection Dialog.
The only way i've got it working, was to put the NVIC002 App between PWMSVM01 and ADC002.
How is the PWMSVM001 supposed to be used for DC Link Current measurement?
Regards
3 Replies
Not applicable
Jul 01, 2014
10:12 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jul 01, 2014
10:12 PM
Hi Daniel,
Perhaps you can take a look on PWSMFOCSL01/02 Apps.
BR,
Zain
Perhaps you can take a look on PWSMFOCSL01/02 Apps.
BR,
Zain
Jul 02, 2014
12:49 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jul 02, 2014
12:49 AM
Hello Zain,
thanks, i've got PMSMFOCSL01 App installed. But in the signal assignments i can see that the trigger signal is also routed via an Interrupt (internal connection: "NVIC Node").
So it seems there's no way to interconnect the trigger slice to the adc trigger without an NVIC app?
In my opinion i should be able to configure them in the Signal Assignment Dialog via connection of the "Current Trigger Slice Status" (CCU8x.ST3A/B) to the ADC002 Trigger (as shown in the CCU8 Device Guide Fig. 72 and VADC Device Guide Fig. 77).
Why does Dave force me to use an NVIC Node?
Regards,
Daniel
Edit:
I'm using XMC4500 and XMC4400 on Relax Kit board...
thanks, i've got PMSMFOCSL01 App installed. But in the signal assignments i can see that the trigger signal is also routed via an Interrupt (internal connection: "NVIC Node").
So it seems there's no way to interconnect the trigger slice to the adc trigger without an NVIC app?
In my opinion i should be able to configure them in the Signal Assignment Dialog via connection of the "Current Trigger Slice Status" (CCU8x.ST3A/B) to the ADC002 Trigger (as shown in the CCU8 Device Guide Fig. 72 and VADC Device Guide Fig. 77).
Why does Dave force me to use an NVIC Node?
Regards,
Daniel
Edit:
I'm using XMC4500 and XMC4400 on Relax Kit board...
Not applicable
Jul 11, 2014
02:10 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jul 11, 2014
02:10 AM
Hi Daniel,
Thank you very much for the feedback. I've submitted an eTicket 711778215.
Best regards,
Sophia
Thank you very much for the feedback. I've submitted an eTicket 711778215.
Best regards,
Sophia