Jul 28, 2021
08:55 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jul 28, 2021
08:55 AM
Hello,
I am looking at the datasheet of TLE7181EM, Rev 1.2 2019-03-14.
The Table 7, PWM/DIR interface normal operation does not makes sense
When DIR is se to 1 - All HighSide and Low-Side switches are turned OFF.
I believe there is a typo in this table and the DIR & DRVDIS table columns are swapped. Can anyone confirm if this is the correct ?
I am looking at the datasheet of TLE7181EM, Rev 1.2 2019-03-14.
The Table 7, PWM/DIR interface normal operation does not makes sense
When DIR is se to 1 - All HighSide and Low-Side switches are turned OFF.
I believe there is a typo in this table and the DIR & DRVDIS table columns are swapped. Can anyone confirm if this is the correct ?
Solved! Go to Solution.
Labels
- Labels:
-
ispn:1025:1:0
-
l1:144:1:0
-
l2:1244:1:0
1 Solution
Aug 02, 2021
06:23 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Aug 02, 2021
06:23 PM
Hello Nadeem,
It was confirmed that the two columns are swapped and that it is a documentation mistake.
The new and corrected document is now in the process of being finalized.
Therefore, it will soon be published.
Thank you for catching this error.
Best regards,
Pablo
It was confirmed that the two columns are swapped and that it is a documentation mistake.
The new and corrected document is now in the process of being finalized.
Therefore, it will soon be published.
Thank you for catching this error.
Best regards,
Pablo
4 Replies
Jul 28, 2021
07:00 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jul 28, 2021
07:00 PM
Hello Nadeem,
Thank you for posting on Infineon Forums.
I went through the table you referred to, and as you suggested, the DIR and DRVDIS columns seem to be swapped.
I will check internally about this and get back to you.
Once I have the confirmation, I will let you know.
Thank you for noticing this possible mistake.
Best regards,
Pablo
Thank you for posting on Infineon Forums.
I went through the table you referred to, and as you suggested, the DIR and DRVDIS columns seem to be swapped.
I will check internally about this and get back to you.
Once I have the confirmation, I will let you know.
Thank you for noticing this possible mistake.
Best regards,
Pablo
Jul 29, 2021
02:28 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jul 29, 2021
02:28 PM
Appreciate your help !!! Please let me know when you have an update.
Aug 02, 2021
06:23 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Aug 02, 2021
06:23 PM
Hello Nadeem,
It was confirmed that the two columns are swapped and that it is a documentation mistake.
The new and corrected document is now in the process of being finalized.
Therefore, it will soon be published.
Thank you for catching this error.
Best regards,
Pablo
It was confirmed that the two columns are swapped and that it is a documentation mistake.
The new and corrected document is now in the process of being finalized.
Therefore, it will soon be published.
Thank you for catching this error.
Best regards,
Pablo
Aug 03, 2021
08:53 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Aug 03, 2021
08:53 PM
Pablo Elosegui Garcia wrote:
Hello Nadeem,
It was confirmed that the two columns are swapped and that it is a documentation mistake.
The new and corrected document is now in the process of being finalized.
Therefore, it will soon be published.
Thank you for catching this error.
Best regards,
Pablo
Thank you so much !! Appreciate your help !!!