Dec 29, 2020
11:54 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Dec 29, 2020
11:54 AM
After i installed J-link and Dave 4, when i try to debug i have this problem:
"J-Link GDB Server failed:
Could not connect to target. Please check if target is powered and if ribbon cable is plugged properly.
For more details, see the JLinkGDBServer.exe console."
I'm using a previous version 6.30e, but i had installed a newer version before and i had the same problem.
"J-Link GDB Server failed:
Could not connect to target. Please check if target is powered and if ribbon cable is plugged properly.
For more details, see the JLinkGDBServer.exe console."
I'm using a previous version 6.30e, but i had installed a newer version before and i had the same problem.
- Tags:
- IFX
9 Replies
Jan 05, 2021
08:14 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jan 05, 2021
08:14 AM
anyone can help?
Jan 07, 2021
03:42 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jan 07, 2021
03:42 AM
Hi,
To which evaluation board are you trying to connect?
Regards,
Jesus
To which evaluation board are you trying to connect?
Regards,
Jesus
Jan 08, 2021
03:40 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jan 08, 2021
03:40 AM
I'm using the the XMC 4400 Drive Card.
Thanks
Thanks
Jan 11, 2021
07:00 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jan 11, 2021
07:00 AM
Hello, I'm currently having the same problem to flash the XMC4700 of a P2Go Radar. I tried to install different versions of JLink and to use the respective "JLinkGDBServerCL.exe" in the debugger but still i get this error:
J-Link GDB Server failed:
Could not connect to target. Please check if target is powered and if ribbon cable is plugged properly.
For more details, see the JLinkGDBServerCL.exe console.
Jan 11, 2021
11:02 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jan 11, 2021
11:02 PM
Which debugger probe are you using?
Jan 12, 2021
01:28 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jan 12, 2021
01:28 AM
I'm using XMC4200 as debugger probe (it's the one attached to the radar board)
Jan 12, 2021
11:35 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jan 12, 2021
11:35 PM
Hi,
Ensure device is properly powered.
Regards,
Jesus
Ensure device is properly powered.
Regards,
Jesus
Jan 13, 2021
02:43 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jan 13, 2021
02:43 AM
Although the enumeration with the operatiing system has probably taken place, please check as well that your USB-Cable is really a data cable and not a charging cable only..
Jan 27, 2021
02:43 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jan 27, 2021
02:43 AM
I found out that the problem was that the device was not properly powered with the 3.3 V DC voltage.