Featured Discussions
Hello,
I would like to translate below article into Japanese.
Please confirm to my work.
Thank you & Regards,
Masaya
Hi,
I am doing a research project using CY8CKIT-042 PSoC4 Pioneer Kit (CY8C4245AXI-483). The prototype device is powered from a battery of 40mAh capacity. After the normal mode operation when I power OFF the device, the uC enters into deep sleep power saving mode. From the deep sleep mode when I connect charger for charging the battery or press the power ON key then uC exits from deep sleep mode and enters into normal mode.
However in an extreme case, the battery was weak while the time I powered OFF the device then in between the deep sleep operation state the battery was fully drained and there was no power source to the device and uC wad fully turned OFF.
After the above scenario, when I connect a power source to the device the expected behaviour is that the device should turn ON automatically due to the reset signal that appears on connecting the power source. However, in some scenario the device didn't turned ON and a re-flashing of the uC was required for turning ON and resuming the expected behaviour.
Can anyone suggest some root cause for this behaviour and what could the possible solution to avoid it?
Thanks in advance.
Show LessDoes the TLE9461-3ES generate an error when receiving CAN2.0B 29-bit communications?
Which controller format is 2.0A or 2.0B active or 2.0B passive?
Dear Infineon engineer.
I want to use TLE7386-3E chip to generate 5V, 3.3V, and 1.3V voltages. However, in my design, it's not for MCU. Therefore, for the pins related to reset, RO_1, RO_2, and the pins related to watchdog, WDI, WDO, can I just give them a constant high or low voltage level? That is, I don't need these monitoring functions, as long as the chip can generate voltages normally.
Your help with this matter is invaluable to me, and I thank you in advance.
Doublemint
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/%E7%94%B5%E6%B1%A0%E7%AE%A1%E7%90%86IC/about-TLE7368-3E-watchdog/td-p/741135
Show LessHi members,
I have a problem with SCR debugging.
it is exactly the same as SCR Debugging problem - Infineon Developer Community
I wrote my own SCR code for development and flashed it to AURIX with SCRCFG 0x0.
and changed SCRCFG 0x0 to 0x1 and then everything was good.
SCR worked what I wanted.
But when I changed SCRCFG 0xA and then started SCR, suddenly SCR start address was placed at "_Exit".
So if I want to run the SCR, I should change the address to 0x0.
How can I run the SCR with SCRCFG to 0xA and the start address at 0x0 without any modification about the start address?
Please Let me know.
Show Less
Are the ECU characteristics of the TLE926x series the same?
We are considering whether we need to rerun the EMC test when we change the parts used from TLE9261BQX to TLE9263BQX.
Hi all,
After reflow soldering sensor DSP368 to PCB, i want to add protect holder to PCB, but i need to preheat glue to add the holder. But the glue Heat Cure Time @ 150ºC ,30minutes => Is The sensor DPS368 OK after Heat cure ?
Thanks,
Show LessI tried coneccting CySmart 1.3.0.8 and CY8CKIT-042-BLE-A using default settings.
Then, too many peer devices were listed in master tab.
Could I delete peer devices from list when I push [start scan]?
and is there a way to display only Cypress(Infineon) devices on master tab?
Or Could I serch and sort devices with device name?
best regards
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/PSoC-4/CySmart-configuration/td-p/741035
Show LessHello,
Now I can use one TIMER to set one time interval and trigger one event as shown in the picture below.
And project is also attached.
Is it possible that I only use one timer to trigger different event according to different time interval?
Thanks!
BR,
Lila
Show Less