Mar 24, 2020
11:24 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Mar 24, 2020
11:24 AM
I am attempting to use UART communication between my Arduino and Position2Go sensor. However, I cannot find a pinout diagram of the Position2Go sensor, nor any information on the topic. Does a diagram exist, and is UART possible with the position2go sensor?
Much thanks to whoever responds!
Much thanks to whoever responds!
Solved! Go to Solution.
1 Solution
Apr 06, 2021
01:28 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Apr 06, 2021
01:28 AM
Hello Federico,
Radar GUI, and C_ComLib provided examples are based on the USB CDC interface.
You need to implement you own UART redirection functions to see RAW data sent via serial communication to HyperTerminal.
Best Regards,
Montassar.
Radar GUI, and C_ComLib provided examples are based on the USB CDC interface.
You need to implement you own UART redirection functions to see RAW data sent via serial communication to HyperTerminal.
Best Regards,
Montassar.
3 Replies
Jul 03, 2020
03:34 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jul 03, 2020
03:34 AM
Hi Drago627,
Please refer to the HW/Schematics/P2G_Schematics_V1.2.pdf file under the IFX_P2G-HW-SW_V1.0.2 package.
In order to get the P2G package, please download and install Infineon Toolbox, then look for Position2Go (refer to to the 24GHz_Radar_Tools_and_Development_Environment_User _Manual)
Best Regards,
Montassar
Please refer to the HW/Schematics/P2G_Schematics_V1.2.pdf file under the IFX_P2G-HW-SW_V1.0.2 package.
In order to get the P2G package, please download and install Infineon Toolbox, then look for Position2Go (refer to to the 24GHz_Radar_Tools_and_Development_Environment_User _Manual)
Best Regards,
Montassar
Apr 04, 2021
02:41 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Apr 04, 2021
02:41 PM
Hello,
I am facing the same problem with the Position2Go board: UART data is not present on the PIN.
From the Radar GUI (and the USB C code) I am able to read the RAW ADC I/Q data (USB).
However, nothings can be seen on the UART (Pin 7/8 on J1).
Do I need to enable the UART by adjusting the firmware?
In the manual ("24ghz radar tool and development environment user manual") it seems that only Sense2GoL board supports UART, is that the case?
Thank you in advance for your help,
Federico
I am facing the same problem with the Position2Go board: UART data is not present on the PIN.
From the Radar GUI (and the USB C code) I am able to read the RAW ADC I/Q data (USB).
However, nothings can be seen on the UART (Pin 7/8 on J1).
Do I need to enable the UART by adjusting the firmware?
In the manual ("24ghz radar tool and development environment user manual") it seems that only Sense2GoL board supports UART, is that the case?
Thank you in advance for your help,
Federico
Apr 06, 2021
01:28 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Apr 06, 2021
01:28 AM
Hello Federico,
Radar GUI, and C_ComLib provided examples are based on the USB CDC interface.
You need to implement you own UART redirection functions to see RAW data sent via serial communication to HyperTerminal.
Best Regards,
Montassar.
Radar GUI, and C_ComLib provided examples are based on the USB CDC interface.
You need to implement you own UART redirection functions to see RAW data sent via serial communication to HyperTerminal.
Best Regards,
Montassar.