infineon4engineers Facebook

infineon@google+ Google+

infineon@linkedin linkedin

infineon4engi@twitter twitter

infineon@youtube youtube

Search:

Type: Posts; User: Srivatsa

Search: Search took 0.01 seconds.

  1. Hi, Pls contact the respective Infineon sales /...

    Hi,
    Pls contact the respective Infineon sales / application engineer in your region. They will assist you with further inputs.
    Thanks
  2. Replies
    1
    Views
    549

    Hi We see no issue in using only two legs of...

    Hi

    We see no issue in using only two legs of the IGCM20F60GA. What is the switching frequency / duty cycle and the bootstrap capacitor value? Make sure there is sufficient time to charge the...
  3. Replies
    33
    Views
    9,913

    Sticky: Hi Cody, General design guides are available...

    Hi Cody,

    General design guides are available at [URL="https://www.infineon.com/dgdl/Infineon-HV_Floating_MOS_Gate_Drivers_AN978-AN-v01_00-EN.pdf?fileId=5546d462533600a40153559f7cf21200"]

    and
    ...
  4. Replies
    2
    Views
    565

    Thank you. You can visit www.infineon.com/gd and...

    Thank you. You can visit www.infineon.com/gd and look into the Documents section. Under Application Notes in this section you will find more application notes / manuals similar to the AN978.
  5. Replies
    1
    Views
    721

    Hi Abhijit, For a given gate resistor Rg,...

    Hi Abhijit,

    For a given gate resistor Rg, IOUTH and IOUTL depend on the VCC2 and VEE2. By changing Rg, the output current delivered to the gate can be varied.

    The charging/discharging current...
  6. Arun, What is the status of SD pin? It is to...

    Arun,

    What is the status of SD pin? It is to be low for normal operation. See fig 1 in IR2110 datasheet.
    Also, the driver has a undervoltage lock-out protection of 9.7 V. Check to make sure the...
  7. Hi Arun, It looks like the bootstrap capacitor...

    Hi Arun,

    It looks like the bootstrap capacitor is not sufficiently charged to turn on the high side output. What is the duty cycle? Make sure the low side is turned on long enough to charge the 47...
  8. Replies
    2
    Views
    616

    Hi Abhijit, The "2nd current" is not...

    Hi Abhijit,

    The "2nd current" is not specified. Figure 7-10 of datasheet shows the total timing for the two level turn time TLSET as a function of the external capacitor CTLSET.
    This covers non...
  9. Replies
    4
    Views
    865

    Distributor restocking should begin by end of...

    Distributor restocking should begin by end of March or early April. Please contact local Infineon sales team for further information. Thanks.
  10. Replies
    4
    Views
    865

    The differences between 6ED003L02-F2 and...

    The differences between 6ED003L02-F2 and 6EDL04N02PR are:

    1. The control logic of HIN and LIN inputs. 6ED003L02-F2 has negative logic and 6EDL04N02PR has positive logic.
    2. The undervoltage...
  11. Replies
    1
    Views
    383

    The 6EDL04N02PR acts as per the input provided....

    The 6EDL04N02PR acts as per the input provided. All outputs are set to LOW, if EN is at LOW logic level. When EN is HIGH, the outputs are driven by the input. In the above case when enable is low,...
  12. Replies
    2
    Views
    828

    What is the VDD and VCC voltage in your design? ...

    What is the VDD and VCC voltage in your design?

    The Sd pin has a weak pull down internally. It is recommended to ground the pin if unused.
  13. Replies
    2
    Views
    2,709

    Hi, Our quality team has sent across the FIT...

    Hi,

    Our quality team has sent across the FIT data for IR2010SPBF over email.

    Thanks and regards,

    Srivatsa
  14. Thread: 1edi2002as

    by Srivatsa
    Replies
    1
    Views
    1,529

    Hi, Thanks for your question. We are unable to...

    Hi,

    Thanks for your question. We are unable to answer this query on the public forum.

    Pls contact your local Infineon field application engineer or sales person who can internally route the...
  15. Yes, the COM pin and VSS pin can be joined...

    Yes, the COM pin and VSS pin can be joined together.

    The 6EDL04N06PT can be used with 3 current shunt resistors.

    In this case the ITRIP pin of 6EDL04N06PT can be used to detect current from...
Results 1 to 15 of 15
Disclaimer

All content and materials on this site are provided “as is“. Infineon makes no warranties or representations with regard to this content and these materials of any kind, whether express or implied, including without limitation, warranties or representations of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, whether express or implied, is granted by Infineon. Use of the information on this site may require a license from a third party, or a license from Infineon.


Infineon accepts no liability for the content and materials on this site being accurate, complete or up- to-date or for the contents of external links. Infineon distances itself expressly from the contents of the linked pages, over the structure of which Infineon has no control.


Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Usage Terms of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Usage Terms of this site. Infineon reserves the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.