Search:

Type: Posts; User: MMarquardt

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    492

    Are you sure your ADICR.INTCT value is correctly...

    Are you sure your ADICR.INTCT value is correctly set? This defines the behavior when an interrupt will be triggered.
  2. Thread: Standby RAM

    by MMarquardt
    Replies
    8
    Views
    2,212

    When the trap occurs the SW should go to the trap...

    When the trap occurs the SW should go to the trap handler and break there (__debug instruction).
    From the trap handler that is called you know the trap class. Corresponding Trap ID can be read from...
  3. Thread: Standby RAM

    by MMarquardt
    Replies
    8
    Views
    2,212

    I can see that this address should be valid since...

    I can see that this address should be valid since it addresses locally the DSPR of CPU0. Did you check which trap handler is called (=trap class) and the Trap Identification Number (in D15)?
  4. Hi, I hope the following code snippet does help....

    Hi, I hope the following code snippet does help. It is for TC2xx devices and not necessarily tested on TC27x. so maybe you need to adapt some multiplexer settings:

    //Here do not forget to enable...
  5. Thread: Standby RAM

    by MMarquardt
    Replies
    8
    Views
    2,212

    It would help if you would provide the name of...

    It would help if you would provide the name of the device you are using. Most probably the RAM where you are trying to copy something in is:
    - protected by MPU or SPROT
    - is unitialized
    -you are...
  6. Replies
    1
    Views
    1,150

    The perhipheral module subchapter of each module...

    The perhipheral module subchapter of each module contains a list of registers of that module. This table has a column "Access Mode" that shows for the Write Accesses the access restrictions.
    Here...
  7. Check the Errata Sheet of the specific device....

    Check the Errata Sheet of the specific device. For some devices special care needs to be taken when initializing the PLL (workarounds).
    This is the most likely reason. Others would be wrong...
  8. Replies
    2
    Views
    1,969

    I did not check the content you programmed in...

    I did not check the content you programmed in detail but most likely you did enable the Hardware Security Module without having valid code for it in the Flash. This leads to a situation where...
  9. Replies
    2
    Views
    1,299

    The latest release would be release 405. It is...

    The latest release would be release 405.
    It is done according to Autosar 4.0 but as far as I know it can be used in Autosar 4.2 setups as well. Best would be to contact a BSW integrator about that.
  10. Replies
    2
    Views
    2,197

    Hi, those are both timer modules but have totally...

    Hi, those are both timer modules but have totally different structure. GPT is quite simple while the GTM is very powerful but also more complex. They are described in the User Manual of the...
  11. Replies
    1
    Views
    1,722

    Hi, here you will only get answers regarding...

    Hi, here you will only get answers regarding device specifics not IT support. There should be a link when you are logged in where you can get IT support. They should be able to help.
  12. no MMU available

    Hi,

    there is no MMU implemented in that device. It only has an MPU.
  13. Replies
    1
    Views
    3,007

    Interrupt Chain

    Unfortunately the provided files do not help to follow the interrupt chain.
    You need to verify the following:
    1) Is the interrupt event generated inside the GTM? This means: Is the timer correctly...
  14. Replies
    1
    Views
    2,767

    Basically this is shown when you have selected an...

    Basically this is shown when you have selected an absolute restriction on a certain function/variable then it is not selected in a generic part of the linker script.
  15. Replies
    2
    Views
    2,584

    There is no information which OS you are using...

    There is no information which OS you are using nor further explanation regarding your setup. In case you expect a wrong configuration or hardware fail as the root cause of your issue you should...
  16. Thread: Tc27xx vadc

    by MMarquardt
    Replies
    3
    Views
    2,516

    I would say you forgot to enable the analog part...

    I would say you forgot to enable the analog part of the VADC group you are using. Check bit field ANONS/ANONC of register GxARBCFG.
  17. Hi, if you Register on www.myinfineon.com and...

    Hi,

    if you Register on www.myinfineon.com and then send your account Name to aurix@Infineon.com asking for the Access to the AURIX documentation you will be granted Access to the documentation...
  18. Replies
    1
    Views
    1,977

    You do not need to reroute. You just configure...

    You do not need to reroute. You just configure both peripherals to use the signal from the same input pin.
  19. Replies
    4
    Views
    7,705

    Trigger

    Hi,
    you need to trigger a Shadow Transfer. Set bit TCTR0.STE12.
    Regards
  20. Replies
    2
    Views
    6,439

    Hello RRoman, I do not know why Dave2 is...

    Hello RRoman,

    I do not know why Dave2 is complaining about this but what I do know is that
    you should be able to do what you want if you use our SCU driver for XC2000.
    You can find it here:...
  21. Replies
    3
    Views
    13,432

    Hi VTrapp, I do not know where exactly the...

    Hi VTrapp,

    I do not know where exactly the problem lays but I got a solution as
    described in my post Error when trying to add apps:
  22. Replies
    1
    Views
    3,757

    Solution

    If anyone ever experiences similar problems:

    1) Delete/Rename the folder Users/yourusername/Infineon/D3LibraryAppStore
    2) Create a new folder with the name D3LibraryAppStore in the same folder...
  23. Replies
    1
    Views
    3,757

    Error when adding apps

    Hi,

    I get an error when trying to add an app:

    Failed during constraing posting

    I already tried to reinstall.
  24. Replies
    5
    Views
    10,159

    If you are still interested in this, I can...

    If you are still interested in this, I can provide Information on the ADC and the CCU6, just write me a pn.
Results 1 to 24 of 24
Disclaimer

All content and materials on this site are provided “as is“. Infineon makes no warranties or representations with regard to this content and these materials of any kind, whether express or implied, including without limitation, warranties or representations of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, whether express or implied, is granted by Infineon. Use of the information on this site may require a license from a third party, or a license from Infineon.


Infineon accepts no liability for the content and materials on this site being accurate, complete or up- to-date or for the contents of external links. Infineon distances itself expressly from the contents of the linked pages, over the structure of which Infineon has no control.


Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Usage Terms of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Usage Terms of this site. Infineon reserves the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.