infineon4engi@twitter infineon@linkedin infineon4engineers infineon@youtube
twitter Facebook Linkedin Youtube

Search:

Type: Posts; User: forix

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    805

    The SSC interface has the defaut push-pull...

    The SSC interface has the defaut push-pull configuration. To use the open-drain configuration the bit SSC_OD has to be used.See sections 3.7/3.8 in the user's manual.
  2. The transmission cycle begins when the chip is...

    The transmission cycle begins when the chip is selected by the input CSN (Chip Select Not), LOW active. After the CSN input returns from LOW to HIGH, the word that has been read is interpreted...
  3. Replies
    1
    Views
    652

    Just connect VS to 5V. See als 3.3V design here...

    Just connect VS to 5V. See als 3.3V design here TLE4966K Hall switch Shield2Go.
  4. DIAG# pin has a pullup resistor? VCC is 3.3V Can...

    DIAG# pin has a pullup resistor? VCC is 3.3V Can you please comment on the osci screenshots and signal levels? The TAB is connected to Vbb? Vbb is > 11V? The two voltage domains VCC and VBB are...
  5. The output pin DIAG# provides an open drain...

    The output pin DIAG# provides an open drain functionality. A current source is also connected to the pin DIAG#. In normal operation the signal DIAG is high. When overtemperature or Vbb below ON-Limit...
  6. The SPI Mode of the ISO1H816G as SPI slave is...

    The SPI Mode of the ISO1H816G as SPI slave is Mode=2. MSB first, SCLK idle = High. At CS# = Low -> SO data out on falling edge of clock, SI data in on rising edge of the clock.

    The description of...
  7. You may try this: Library for Infineons's 3D...

    You may try this: Library for Infineons's 3D magnetic sensor TLE493D for Arduino.
    https://github.com/Infineon/TLE493D-3DMagnetic-Sensor
  8. Replies
    1
    Views
    1,762

    What controller are you talking about, which part...

    What controller are you talking about, which part number?
  9. Replies
    1
    Views
    1,483

    Excerpt from data sheet -> Managing correct...

    Excerpt from data sheet ->
    Managing correct sensor read outs by the C:
    This sensor does not incorporate shadow-buffers for readout. Thus, it is mandatory to read the sensor data
    not during a...
  10. Replies
    1
    Views
    2,248

    I think the reason for the encryption of...

    I think the reason for the encryption of simulation models is to protect intellectual property. Are you using full version of Simplis, whih probably can handle encrypted model?
  11. Replies
    1
    Views
    3,055

    I think the generated OTP file in MCEProgrammer...

    I think the generated OTP file in MCEProgrammer for IRMCK099 is not encrypted, You can read with a hex viewer/editor. For the IRMCx100, with 8051 controller, the MCECompiler encrypts the OTP file for...
  12. Replies
    3
    Views
    2,781

    How about Interface Mode2 Register, are you using...

    How about Interface Mode2 Register, are you using autocalibration? Asking this as activated autocalibration forces 360 angle range regardless of ANG_RANGE setting. Refer to page 88/89 of the manual.
  13. Replies
    6
    Views
    3,334

    There is a library source code for Arduino...

    There is a library source code for Arduino available on github supporting TLE5012B. Check the source code here.
  14. Replies
    3
    Views
    2,781

    You may consult the manual...

    You may consult the manual section "6.1.3 Signed registers and Twos complement" where it is explained how to interpret the 15bit ANG_VAL register value and calculate the angle. By the way, which...
  15. You wrote: ...because of the lower voltage supply...

    You wrote: ...because of the lower voltage supply at J4 (< 20 volts)..

    Figure 14 on page 20 of the user manual is showing the circuitry you mentioned. In case you remove R32 and R39 (R35 = bridge...
  16. Replies
    1
    Views
    3,988

    Probably the ESD spec for this MosFET you will...

    Probably the ESD spec for this MosFET you will have to request via the TAC form.
  17. Replies
    3
    Views
    2,451

    Infineon-100serieskitmceinstaller-SW-v03_05-EN.exe...

    Infineon-100serieskitmceinstaller-SW-v03_05-EN.exe, defaults accepted during install, installs the 099 compiler to c:\iMotion\MCE Compiler\bin.

    You should consult the users manual concerning...
  18. This question is about reliability. You will have...

    This question is about reliability. You will have to request FIT data via this link.
  19. Replies
    3
    Views
    1,951

    You will find the description of the GPIO ports...

    You will find the description of the GPIO ports in the User's Manual section "2.4.2 General Purpose I/O" on page 28
    ->...
  20. Replies
    6
    Views
    3,334

    Please try one of the C-code samples provided in...

    Please try one of the C-code samples provided in section "5.2.4 Cyclic Redundancy Check (CRC)" of the user's manual?
  21. Replies
    1
    Views
    2,277

    See section 6.2 For ORCAD and change the settings...

    See section 6.2 For ORCAD and change the settings for the simulation options.
    LINK
  22. Replies
    1
    Views
    1,957

    See figure 6 in the datasheet...

    See figure 6 in the datasheet. According to your maximum gate current IGmax you wish to drive, which depends on switch on/off time and frequency, the gate resistor's value is approx RG=12V/IGmax.
  23. Replies
    1
    Views
    2,209

    You will have to consult the "pin definition and...

    You will have to consult the "pin definition and function" table in the datasheet to understand the symbols like VDH (e.g. voltage drain high), VDHS (switched Output of VDH), VS (voltage supply) and...
  24. Replies
    1
    Views
    3,464

    You can select an online distributor in China on...

    You can select an online distributor in China on this Infineon page https://www.infineon.com/cms/cn/product/where-to-buy/ .
  25. Replies
    1
    Views
    2,167

    The component T1-T2 is a NTC element you can use...

    The component T1-T2 is a NTC element you can use to estimate the temperature of the IGBTs of the module. What are the values of the components shown in the attached picture of the 6ED003L02? What is...
Results 1 to 25 of 74
Page 1 of 3 1 2 3
Disclaimer

All content and materials on this site are provided as is. Infineon makes no warranties or representations with regard to this content and these materials of any kind, whether express or implied, including without limitation, warranties or representations of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, whether express or implied, is granted by Infineon. Use of the information on this site may require a license from a third party, or a license from Infineon.


Infineon accepts no liability for the content and materials on this site being accurate, complete or up- to-date or for the contents of external links. Infineon distances itself expressly from the contents of the linked pages, over the structure of which Infineon has no control.


Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Usage Terms of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Usage Terms of this site. Infineon reserves the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.