Search:

Type: Posts; User: Jing.N

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    3,384

    Could you please share the input pattern you use?...

    Could you please share the input pattern you use? Example: IN = 1, INH = 1; --> IN = 0, INH = 0 --> ...
    Maybe also some screen shot from waveform, so we can help you more in details.
  2. Replies
    7
    Views
    3,384

    Yes, the one we described in chapter 3.2.2 in our...

    Yes, the one we described in chapter 3.2.2 in our application note. It causes power dissipation and might destroy the device.
  3. Replies
    7
    Views
    3,384

    Maybe you can check the output voltage to see if...

    Maybe you can check the output voltage to see if you have undervoltage toggling there. If yes, the overtemperature protection could react too late to protect the device.
  4. Replies
    7
    Views
    3,384

    Please check the voltage at VS pin. Changing the...

    Please check the voltage at VS pin. Changing the motor direction without a proper braking could cause a high voltage at VS pin. If the motor is still working as a generator, the voltage might exceed...
  5. Replies
    1
    Views
    3,511

    Please see my comments below: 1. Can the IFX007T...

    Please see my comments below:
    1. Can the IFX007T be used to perform the same function by holding the IN pin low and applying the PWM signal to the INH pin?
    Yes, it can be used to perform this...
  6. Replies
    1
    Views
    3,249

    Yes, you can connect two current sense pin to the...

    Yes, you can connect two current sense pin to the ADC pin of the microcontroller.
    Please be noticed when LS is ON the IIS(offset) is present at IS pin. It means if you connect two current sense...
  7. Replies
    9
    Views
    6,483

    Hi, The max. voltage of the input depends on...

    Hi,

    The max. voltage of the input depends on the MCU you use. E.g. For Arduino Uno, the max. voltage of I/O pin is VCC+0.5V, it means for 5V supply the max. voltage at I/O pin is 5.5V. Please...
  8. Replies
    9
    Views
    6,483

    The diode should not exceed the max. rating of...

    The diode should not exceed the max. rating of the voltage at ADC pin. I think the diode in datasheet is specified for dedicate MCU.

    Regards,

    Jing
  9. Replies
    9
    Views
    6,483

    Hi, You can use a diode as shown in the figure...

    Hi,

    You can use a diode as shown in the figure below to make sure that the voltage at ADC pin won't exceed the max. rating:
    5118

    22700 is the typical current sense ratio specified in the...
  10. Replies
    9
    Views
    6,483

    Hi, BTS7702 and BTS7708 do not belong to...

    Hi,

    BTS7702 and BTS7708 do not belong to NovalithIC family.

    According to the datasheet of BTS7702, the max. current appears at IS pin is IIS(SAT),Max = 15mA. If the Rsense is 1.2k, the max....
  11. Thread: Ifx007

    by Jing.N
    Replies
    1
    Views
    5,861

    Hi, Are you using the Arduino Shield? Or you...

    Hi,

    Are you using the Arduino Shield? Or you simulate the circuit?
    Could you please provide the input signal and output current? We can help you better with more detailed information.

    Regards,
  12. Replies
    1
    Views
    4,917

    Thanks very much for choosing IFX product....

    Thanks very much for choosing IFX product. Unfortunately IFX9201SG doesn't belong to NovalithIC/TrilithIC family.
    Maybe you can try Infineon online support:...
  13. Replies
    4
    Views
    7,860

    Theoretically it is ok to PWM the INH when IN is...

    Theoretically it is ok to PWM the INH when IN is set to HIGH. But in this case the delay on/off time can be affected due to the enable/disable phase. The protection features are still valid in this...
  14. Hi David, Yes, you are right. With the output...

    Hi David,

    Yes, you are right. With the output capacitors the current should be around 200mA. But the power dissipation of the IFX007T should not be 18V * 200mA. E.g. when we switch on the HS, the...
  15. Sticky: Power Dissipation Tool is released for BTN8962TA/BTN8982TA

    Power dissipation tool for BTN8962TA/BTN8982TA is available in infineon toolbox now!!!

    Download Infineon Toolbox
  16. Replies
    3
    Views
    3,904

    If one half bridge works fine but the other...

    If one half bridge works fine but the other doesn't work properly, normally the issue comes from your board, not the device itself.
    Please check the PCB and the layout. If it possible, you can also...
  17. Replies
    1
    Views
    5,602

    The high level and low level threshold for IHx...

    The high level and low level threshold for IHx and ILx are the same.
  18. Replies
    1
    Views
    1,912

    Thanks for your interest. You don't need any...

    Thanks for your interest. You don't need any other additional components.
  19. Replies
    1
    Views
    2,001

    Sorry for my late reply. You can control the...

    Sorry for my late reply.

    You can control the board by using the Arduino card directly, and you don't need to put additional components.
    The board is XMC1100 Boot Kit compatible as well. But...
  20. Replies
    1
    Views
    2,812

    Thanks very much for your interest. For...

    Thanks very much for your interest.

    For BTN8982TA: The parameters specified in our datasheet might have deviation when the voltage is higher than 18V.
    For IFX007T: According to industrial...
  21. Thanks very much for your interest. Please...

    Thanks very much for your interest.


    Please find some comments below:

    PWM frequency: 31250Hz is only the base frequency. The resulting frequency is equal to the base frequency divided by
    ...
  22. Replies
    0
    Views
    1,320

    IFX007T based motor driver

    https://www.youtube.com/watch?v=TESM-cHDjNs
  23. Replies
    1
    Views
    4,357

    We recommend you to consider BTM7750G and...

    We recommend you to consider BTM7750G and BTM7710G to replace it.

    Please find the product overview below:

    4158


    4159
  24. Replies
    1
    Views
    3,602

    Please look into the replacement guide: ...

    Please look into the replacement guide:
    https://www.infineonforums.com/threads/10383-Replacement-guide-for-TrilithIC-products-to-be-phased-out

    you can find the discontinued device and the...
  25. Replies
    1
    Views
    2,082

    The normal operating voltage range of VS is from...

    The normal operating voltage range of VS is from 8V to 18V. All parameters are specified within this VS range.
    The device can be used in extended range up to 40V as well. But the parameters might...
Results 1 to 25 of 54
Page 1 of 3 1 2 3
Disclaimer

All content and materials on this site are provided “as is“. Infineon makes no warranties or representations with regard to this content and these materials of any kind, whether express or implied, including without limitation, warranties or representations of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, whether express or implied, is granted by Infineon. Use of the information on this site may require a license from a third party, or a license from Infineon.


Infineon accepts no liability for the content and materials on this site being accurate, complete or up- to-date or for the contents of external links. Infineon distances itself expressly from the contents of the linked pages, over the structure of which Infineon has no control.


Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Usage Terms of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Usage Terms of this site. Infineon reserves the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.