infineon4engi@twitter infineon4engineers infineon@linkedin infineon@youtube
twitter Facebook Linkedin Youtube

Search:

Type: Posts; User: rephlex303

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    2,959

    Just found an issue - In the DAVE app...

    Just found an issue - In the DAVE app configuration, the max value for "Ticks per revolution" is listed as 65535
    however this is multiplied by 4 in the encoder_posif_conf.c file for...
  2. Replies
    13
    Views
    2,959

    Also is there any reason why the ENCODER_POSIF...

    Also is there any reason why the ENCODER_POSIF app does not support the XMC1400 Series devices?
  3. Replies
    13
    Views
    2,959

    I was notified about the update when I ran Dave...

    I was notified about the update when I ran Dave this morning.

    Some of the documentation is a bit incomplete though (missing example code etc.):

    void ENCODER_POSIF_Start ( ENCODER_POSIF_t...
  4. Replies
    13
    Views
    2,959

    Hi Jesus, is there any chance I could give the...

    Hi Jesus, is there any chance I could give the posif dave app a trial before it is released?
  5. Replies
    1
    Views
    1,050

    Install the Dave UART app. Read the manual for...

    Install the Dave UART app. Read the manual for the Dave UART app. There will be an example of this in in manual. Avoid interrupts if possible as they are slow.
  6. Misread on ADC around Vref/2 with XMC 4700

    Hi,
    I'm having an issue where I'm getting a misread by the ADC. Any value between ~1845 to 2048 is read as 2048. I am sampling a ~4kHz sine wave at 25kHz.
    I'm using the VADC_GROUP_CONFIG app....
  7. One thing I am still having an issue with is...

    One thing I am still having an issue with is getting the hysteresis band to work. Does anyone know how you would go about doing this? Does the XMC 4700 have hysteresis automatically or does it have...
  8. I have managed to get something working that will...

    I have managed to get something working that will be good enough for my applicacation. However I still can't get the Boundary Check to work correctly.

    The working setup uses an autoscan low...
  9. XMC 4700 ADC Boundary Check used to trigger Counter APP

    Hi,
    I have an XMC 4700.
    I have a 6kHz sine wave connected to P14.1.
    I am using the ADC_MEASUREMENT_ADV app and the COUNTER_APP.

    I would like to count the number of times the sine wave crosses...
  10. Hi Jesus, I have now managed to get it to work...

    Hi Jesus,
    I have now managed to get it to work successfully, however it wasn't as easy as you described!

    I enabled the I2C interrupt mode and the code now got stuck with TDV bit enabled -...
  11. Thanks for that Jesus, I'll give it a go this...

    Thanks for that Jesus, I'll give it a go this week and let you know how I get on.

    Nico
  12. XMC I2C_MASTER APP getting stuck with no slave connected

    Hi,
    I have an XMC-1404 running the I2C_MASTER app connected to a LCD screen with an I2C expander.

    If the LCD is not connected or there is an error in the transmission the APP gets stuck at line...
  13. Thanks for that Jesus, I have removed the LED...

    Thanks for that Jesus, I have removed the LED signal and it works perfectly. I might need to reinable it at some point in the future but by then a new version of the app will be released. I couldn't...
  14. SDMMC app upgrade issues (4.0.22 -> 4.3.22

    Hi,
    I have an XMC 1404 connected to a SD card via the SPI bus.

    I'm using the standard FATFS App with the default main and configurations as described in the FATFS help documentation.

    I've...
Results 1 to 14 of 14
Disclaimer

All content and materials on this site are provided “as is“. Infineon makes no warranties or representations with regard to this content and these materials of any kind, whether express or implied, including without limitation, warranties or representations of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, whether express or implied, is granted by Infineon. Use of the information on this site may require a license from a third party, or a license from Infineon.


Infineon accepts no liability for the content and materials on this site being accurate, complete or up- to-date or for the contents of external links. Infineon distances itself expressly from the contents of the linked pages, over the structure of which Infineon has no control.


Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Usage Terms of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Usage Terms of this site. Infineon reserves the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.