Search:

Type: Posts; User: Jing.N

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    2,193

    Theoretically it is ok to PWM the INH when IN is...

    Theoretically it is ok to PWM the INH when IN is set to HIGH. But in this case the delay on/off time can be affected due to the enable/disable phase. The protection features are still valid in this...
  2. Hi David, Yes, you are right. With the output...

    Hi David,

    Yes, you are right. With the output capacitors the current should be around 200mA. But the power dissipation of the IFX007T should not be 18V * 200mA. E.g. when we switch on the HS, the...
  3. Sticky: Power Dissipation Tool is released for BTN8962TA/BTN8982TA

    Power dissipation tool for BTN8962TA/BTN8982TA is available in infineon toolbox now!!!

    Download Infineon Toolbox
  4. Replies
    3
    Views
    1,076

    If one half bridge works fine but the other...

    If one half bridge works fine but the other doesn't work properly, normally the issue comes from your board, not the device itself.
    Please check the PCB and the layout. If it possible, you can also...
  5. Replies
    1
    Views
    2,341

    The high level and low level threshold for IHx...

    The high level and low level threshold for IHx and ILx are the same.
  6. Replies
    1
    Views
    507

    Thanks for your interest. You don't need any...

    Thanks for your interest. You don't need any other additional components.
  7. Replies
    1
    Views
    539

    Sorry for my late reply. You can control the...

    Sorry for my late reply.

    You can control the board by using the Arduino card directly, and you don't need to put additional components.
    The board is XMC1100 Boot Kit compatible as well. But...
  8. Replies
    1
    Views
    1,169

    Thanks very much for your interest. For...

    Thanks very much for your interest.

    For BTN8982TA: The parameters specified in our datasheet might have deviation when the voltage is higher than 18V.
    For IFX007T: According to industrial...
  9. Thanks very much for your interest. Please...

    Thanks very much for your interest.


    Please find some comments below:

    PWM frequency: 31250Hz is only the base frequency. The resulting frequency is equal to the base frequency divided by
    ...
  10. Replies
    0
    Views
    235

    IFX007T based motor driver

    https://www.youtube.com/watch?v=TESM-cHDjNs
  11. Replies
    1
    Views
    1,666

    We recommend you to consider BTM7750G and...

    We recommend you to consider BTM7750G and BTM7710G to replace it.

    Please find the product overview below:

    4158


    4159
  12. Replies
    1
    Views
    803

    Please look into the replacement guide: ...

    Please look into the replacement guide:
    https://www.infineonforums.com/threads/10383-Replacement-guide-for-TrilithIC-products-to-be-phased-out

    you can find the discontinued device and the...
  13. Replies
    1
    Views
    844

    The normal operating voltage range of VS is from...

    The normal operating voltage range of VS is from 8V to 18V. All parameters are specified within this VS range.
    The device can be used in extended range up to 40V as well. But the parameters might...
  14. Sticky: Download user manual and example code of the demo board

    Overview of the (BL)DC Motor Control Shield with IFX007T:
    https://www.infineon.com/cms/en/product/evaluation-boards/bldc-shield_ifx007t/

    User manual:...
  15. Replies
    2
    Views
    3,300

    The example code is available now. Please find it...

    The example code is available now. Please find it on Infineon website:
    https://github.com/Infineon/IFX007T-Motor-Control
  16. Sticky: Video: How to make a smoothie with our new Motor Driver (IFX007)

    https://www.youtube.com/watch?v=5yQY-CGptBI
  17. Replies
    1
    Views
    1,003

    Thanks very much for your interest. IFX007T is...

    Thanks very much for your interest.

    IFX007T is the industrial version of BTN8982TA. All parameters are specified at 24v instead of 12V. In case you would like to simulate it by using the spice...
  18. Sticky: Replacement guide for TrilithIC products to be phased out

    Replacement guide for TrilithIC products to be phased out over the next years
    4157
  19. Sticky: View Post

    Replacement guide for NovalithIC™ and Trilith IC products to be phased out over the next years
    4156
  20. Replies
    5
    Views
    7,901

    Ok. Good Luck

    Ok. Good Luck
  21. Replies
    5
    Views
    7,901

    Yes, should be above 1.75V

    Yes, should be above 1.75V
  22. Replies
    7
    Views
    9,729

    I thought you might use more than one IFX007T on...

    I thought you might use more than one IFX007T on one PCB. Sorry for my misunderstanding. Now I understood your point.

    We don't recommend our customers to use two devices for one half bridge. Due...
  23. Replies
    7
    Views
    9,729

    I did thermal simulation for the new mission...

    I did thermal simulation for the new mission profile below:

    Load to Vs
    Vs = 24V
    I = 20A
    PWM-Freq=1KHz
    Duty cycle: 50%
    slew-rate: as fast as possible
    ambient temperature: 25°C
    PCB: 2s2p
  24. Replies
    7
    Views
    9,729

    Since we have protection feature integrated into...

    Since we have protection feature integrated into IFX007T, we won't have any cross current caused by the delay variations. But due to the variation the output duty cycle might be a bit different from...
  25. Replies
    7
    Views
    9,729

    Hi Wilheim, It is possible to use to...

    Hi Wilheim,

    It is possible to use to parallelize IFX007T in PWM mode. Of course the power dissipation highly depends on your mission profile: Vs, I, frequency, switching time(slew rate...
Results 1 to 25 of 42
Page 1 of 2 1 2
Disclaimer

All content and materials on this site are provided “as is“. Infineon makes no warranties or representations with regard to this content and these materials of any kind, whether express or implied, including without limitation, warranties or representations of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, whether express or implied, is granted by Infineon. Use of the information on this site may require a license from a third party, or a license from Infineon.


Infineon accepts no liability for the content and materials on this site being accurate, complete or up- to-date or for the contents of external links. Infineon distances itself expressly from the contents of the linked pages, over the structure of which Infineon has no control.


Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Usage Terms of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Usage Terms of this site. Infineon reserves the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.