infineon4engi@twitter infineon@linkedin infineon4engineers infineon@youtube
twitter Facebook Linkedin Youtube

Search:

Type: Posts; User: Casey

Search: Search took 0.00 seconds.

  1. Please try these instructions. It worked on my...

    Please try these instructions. It worked on my end:

    Programming Eval-M1-101T when IC is in SBSL mode (COMx Down):

    Open MCEDesigner v2.3
    Select file> open latest version of MCEDesigner...
  2. Replies
    11
    Views
    981

    Hello, I have created more detailed...

    Hello,
    I have created more detailed instructions to program an IC while in SBSL mode. These instructions are for a motor drive set-up with evaluation board Eval-M1-101T but you should be able to...
  3. Hi Dwissel, In your other forum question, you...

    Hi Dwissel,
    In your other forum question, you were not able to get the device to connect in MCEDesigner after it failed to program because the IC is now in SBSL mode (still working on getting the...
  4. I have repeated this problem on my own computer...

    I have repeated this problem on my own computer and it is true. If you would like to install an older version of MCEDesigner you MUST uninstall MCEWizard v2.3 first. I will update this post once this...
  5. Unfortunately, we do not have a wizard file yet...

    Unfortunately, we do not have a wizard file yet available for this combination and the release of this file is delayed due to COVID-19. I may be able to provide you one that hasn’t be tested out yet...
  6. Product mismatch is due to firmware and .irc file...

    Product mismatch is due to firmware and .irc file not being the same version. When downloading a new software package from the website, make sure you program your IC with the updated firmware within...
  7. All the available wizard configuration files can...

    All the available wizard configuration files can be downloaded on iMOTION webage under development tools: MCEWizard Configuration files v1.0. No need to register to gain access to these.
  8. View Post

    Hi dwissel,
    First, you don’t need to go through MCEWizard to start MCEDesigner. Maybe if you needed to create a new parameter text file for MCEDesigner, but in this case I don’t think you need to…...
  9. Hi Fabio, You are correct, we do perform quite a...

    Hi Fabio,
    You are correct, we do perform quite a bit of tests on Vdd current. The datasheet only provides the required quiescent current but you can find more information in the IPM application...
  10. The user guide is downloaded with MCEDesigner and...

    The user guide is downloaded with MCEDesigner and should be stored in the same folder as the tool location. Same with the MCEWizard user guide. For information on what you are looking for, I would...
  11. Changing the direction requires the speed to go...

    Changing the direction requires the speed to go down to zero before starting up in reverse direction. When motor speed is too low or motor is stopping, back EMF is too low for flux estimator and PLL...
  12. Replies
    11
    Views
    981

    Hi Nuhdede, I was able to recreate the device...

    Hi Nuhdede,
    I was able to recreate the device failing to program firmware. The issue of why it failed is most likely different but when the device fails and goes in SBSL mode, MCEDesigner will not...
  13. Replies
    11
    Views
    981

    Hi Nuhdede, SBSL mode is the default setting and...

    Hi Nuhdede,
    SBSL mode is the default setting and how the IC comes when purchased. It would need to be programmed with the firmware and the parameters again. Are you able to reprogram? Or is the...
  14. Replies
    11
    Views
    981

    Hi Nuhdede, A couple things to check to help...

    Hi Nuhdede,
    A couple things to check to help debug:

    You said you programmed with IRMC301t firmware. I think this was just a typo but please make sure you are programming with IMC301-A firmware...
  15. Replies
    11
    Views
    981

    Hi Nuhdede, Was the firmware successfully...

    Hi Nuhdede,
    Was the firmware successfully programmed or did you encounter an error? Have you checked the connection to make sure it is trying to connect through the right com port? On top toolbar in...
  16. Replies
    6
    Views
    2,854

    Hello, Are you set on the IRMCF171? Point 4...

    Hello,
    Are you set on the IRMCF171? Point 4 would have to be done with the 8051 processor. The rest can all be done with the MCE Tools. If it is possible I highly recommend upgrading to the IMC101T...
  17. Replies
    6
    Views
    2,854

    Sorry for the delay. You are trying to program...

    Sorry for the delay. You are trying to program the 8051 microcontroller correct? Not the Motion Control Engine (MCE)? Since this is an older part, I believe Keil has renamed their products and it...
  18. Hello, Typically these boards are used with...

    Hello,
    Typically these boards are used with iMOTION controllers so it will be little more difficult for me to understand the problem. What are you reading on PIN 13 (Gatekill) on the iMOTION...
  19. Replies
    6
    Views
    1,600

    230VAC should be no problem as that provides a DC...

    230VAC should be no problem as that provides a DC bus voltage of around 325V. I am not sure how you are seeing 535V unless you were providing more than 230VAC?
    I recommend updating your MCEWizard...
  20. Replies
    6
    Views
    1,600

    How much input AC voltage are you supplying? The...

    How much input AC voltage are you supplying? The IPM on your control board (IRSM505-065) can only support a max DC bus voltage of 400V (breakdown voltage is around 500V) so you will need to lower...
  21. Replies
    6
    Views
    1,600

    Hi Marcuccio1995, What is your DC Bus Over-value...

    Hi Marcuccio1995,
    What is your DC Bus Over-value set as? Please provide me a screenshot of the parameters in MCEWizard (from the advanced page like the example) and I can help you determine what may...
  22. Replies
    6
    Views
    2,854

    Hi Dronnet, Would you still like this firmware...

    Hi Dronnet,
    Would you still like this firmware file? This can be done by using the publicly available FW then using the VF Diagnostic function in MCEDesigner. You can then apply a low DC voltage...
  23. SOLUTION Hi all, This issue that has now been...

    SOLUTION

    Hi all,
    This issue that has now been fixed in revision v1.1 of IMOTION-LINK. All devices shipped past June 2019 have resolved this issue. You can tell the version of your IMOTION-LINK by...
Results 1 to 23 of 23
Disclaimer

All content and materials on this site are provided “as is“. Infineon makes no warranties or representations with regard to this content and these materials of any kind, whether express or implied, including without limitation, warranties or representations of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, whether express or implied, is granted by Infineon. Use of the information on this site may require a license from a third party, or a license from Infineon.


Infineon accepts no liability for the content and materials on this site being accurate, complete or up- to-date or for the contents of external links. Infineon distances itself expressly from the contents of the linked pages, over the structure of which Infineon has no control.


Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Usage Terms of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Usage Terms of this site. Infineon reserves the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.