Search:

Could you please share the input pattern you use? Example: IN = 1, INH = 1; --> IN = 0, INH = 0 --> ...
Maybe also some screen shot from waveform, so we can help you more in details.

Yes, the one we described in chapter 3.2.2 in our application note. It causes power dissipation and might destroy the device.

Maybe you can check the output voltage to see if you have undervoltage toggling there. If yes, the overtemperature protection could react too late to protect the device.

Please check the voltage at VS pin. Changing the motor direction without a proper braking could cause a high voltage at VS pin. If the motor is still working as a generator, the voltage might exceed...

Please see my comments below:
1. Can the IFX007T be used to perform the same function by holding the IN pin low and applying the PWM signal to the INH pin?
Yes, it can be used to perform this...

Yes, you can connect two current sense pin to the ADC pin of the microcontroller.
Please be noticed when LS is ON the IIS(offset) is present at IS pin. It means if you connect two current sense...

Hi,

The max. voltage of the input depends on the MCU you use. E.g. For Arduino Uno, the max. voltage of I/O pin is VCC+0.5V, it means for 5V supply the max. voltage at I/O pin is 5.5V. Please...

The diode should not exceed the max. rating of the voltage at ADC pin. I think the diode in datasheet is specified for dedicate MCU.

Regards,

Jing

Hi,

You can use a diode as shown in the figure below to make sure that the voltage at ADC pin won't exceed the max. rating:
5118

22700 is the typical current sense ratio specified in the...

Hi,

BTS7702 and BTS7708 do not belong to NovalithIC family.

According to the datasheet of BTS7702, the max. current appears at IS pin is IIS(SAT),Max = 15mA. If the Rsense is 1.2k, the max....

Hi,

Are you using the Arduino Shield? Or you simulate the circuit?
Could you please provide the input signal and output current? We can help you better with more detailed information.

Regards,

Thanks very much for choosing IFX product. Unfortunately IFX9201SG doesn't belong to NovalithIC/TrilithIC family.
Maybe you can try Infineon online support:...

Theoretically it is ok to PWM the INH when IN is set to HIGH. But in this case the delay on/off time can be affected due to the enable/disable phase. The protection features are still valid in this...

Hi David,

Yes, you are right. With the output capacitors the current should be around 200mA. But the power dissipation of the IFX007T should not be 18V * 200mA. E.g. when we switch on the HS, the...

Power dissipation tool for BTN8962TA/BTN8982TA is available in infineon toolbox now!!!

Download Infineon Toolbox

If one half bridge works fine but the other doesn't work properly, normally the issue comes from your board, not the device itself.
Please check the PCB and the layout. If it possible, you can also...

The high level and low level threshold for IHx and ILx are the same.

Thanks for your interest. You don't need any other additional components.

Sorry for my late reply.

You can control the board by using the Arduino card directly, and you don't need to put additional components.
The board is XMC1100 Boot Kit compatible as well. But...

Thanks very much for your interest.

For BTN8982TA: The parameters specified in our datasheet might have deviation when the voltage is higher than 18V.
For IFX007T: According to industrial...

Thanks very much for your interest.


Please find some comments below:

PWM frequency: 31250Hz is only the base frequency. The resulting frequency is equal to the base frequency divided by
...

https://www.youtube.com/watch?v=TESM-cHDjNs

We recommend you to consider BTM7750G and BTM7710G to replace it.

Please find the product overview below:

4158


4159

Please look into the replacement guide:
https://www.infineonforums.com/threads/10383-Replacement-guide-for-TrilithIC-products-to-be-phased-out

you can find the discontinued device and the...

The normal operating voltage range of VS is from 8V to 18V. All parameters are specified within this VS range.
The device can be used in extended range up to 40V as well. But the parameters might...