Search:

Type: Posts; User: longtimer

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Seeking example for switching from I2C master to UART and back on one channel

    Hello,

    For system initialization, I have a need to communicate with some chips on my board using the XMC1300 as an I2C master for configuration. After the initial communication, I want to switch...
  2. Operating XMC1300 ADC in slow standby mode

    Hello,

    I have been fighting to get the ADC to operate in "slow standby" mode on an XMC1300 as defined in section 16.5.1 of the reference manual because I am taking infrequent measurements and...
  3. Please change the documentation on page 605 of...

    Please change the documentation on page 605 of the reference manual from " external (outside the ADC) trigger" to " external trigger (outside the ADC)" and a definition is available. The current word...
  4. Please add definition of external trigger to XMC1000 documentation

    Hello,

    In looking at the VADC section of the XMC1300 reference manual, the term "external trigger" is used but never defined. Is this a trigger from a pin on the chip, a trigger from another...
  5. On the XMC1000 version it is 5s if the BMI is set...

    On the XMC1000 version it is 5s if the BMI is set accordingly. Otherwise, I have not seen it timeout. It just sits there.
  6. I always hit problems with the bootstrap loader...

    I always hit problems with the bootstrap loader and related software as it is poorly designed with no intelligent feedback. Try getting the infineon memtool and use it. It is also poor software but...
  7. XMC1300 initialization example without generated code or libraries

    Hello,

    I cannot get the XMC1301 to initialize its ADC, let alone get a reading on a channel as a result of load event.

    I have been pulling down examples to try to use the ADC on XMC1301 but...
  8. Thank you. Hopefully the Infineon documentation...

    Thank you. Hopefully the Infineon documentation folks can add the link in the document for other folks.

    Cheers,

    Jason
  9. Code sampes for application note AP32346

    Hello,

    Can someone please direct me to the code that goes with application note AP32346....
  10. Replies
    1
    Views
    961

    Since no support was offered for this issue, I...

    Since no support was offered for this issue, I had to resolve it myself. Good chips but miserable customer support...

    The issue is that even with the detection delay time set to 0x03 or no delay...
  11. Replies
    2
    Views
    1,341

    Since no support was offered for this issue, I...

    Since no support was offered for this issue, I had to resolve it myself. Good chips but miserable customer support...

    The issue is that even with the detection delay time set to 0x03 or no delay...
  12. Replies
    2
    Views
    1,341

    Checking Power Supply Voltage on XMC1000

    Hi,

    In looking through the reference manual, I couldn't find enough information on the Power Management system about the VDESR flag outputs.

    I have tried the following for checking the voltage...
  13. Replies
    1
    Views
    961

    Voltage monitoring

    Hello,

    In looking through the reference manual, I couldn't find enough information on the Power Management system regarding the VDESR flag outputs.

    I have tried the following for checking the...
  14. Replies
    2
    Views
    1,974

    Hi, I am not sure because I don't get that...

    Hi,

    I am not sure because I don't get that far. The installation puts about 3 Gb on C drive then complains that it needs another 3.7 Gb of space on C drive to install so I am unable to complete...
  15. Replies
    2
    Views
    1,974

    DAVE 4 poor installation just like DAVE 3!

    When I was using DAVE-3.1.10, I reported in these forums that the installation was trying to put Gigs of files on the C drive even through I had selected another drive for installation. I recently...
  16. You are not likely to get good detailed answers...

    You are not likely to get good detailed answers from the Infineon support staff in these forums. The forums seem to be understaffed and have people who don't actually get much time to play with the...
  17. Replies
    2
    Views
    2,084

    Hi Min Wei, Thanks for the details. Can you...

    Hi Min Wei,

    Thanks for the details. Can you pass along to get the documentation fixed such that Fin is update to be Fpin as you pointed out. Fin is hard to find in the document so I was not sure...
  18. DAVE 4 - list of changes compared to DAVE 3

    Hello,

    Is there a list of changes and bug fixes between the latest DAVE 3 and DAVE 4 releases? I did not see it.

    The reason I ask is that JTAG debugging through the miniwiggler in DAVE 3 is...
  19. Replies
    2
    Views
    2,084

    I2C stop condition interrupt

    Hello,

    I have been encountering a condition where the the I2C master and the I2C slave (XMC1100) get out of sync and the master is awaiting more data while the slave thinks it is done.

    In...
  20. Replies
    11
    Views
    14,934

    Hi Jackson, Some of what you are telling me...

    Hi Jackson,

    Some of what you are telling me does not match what I am observing. It is sometimes possible to quit UDAS from the Device Scanner and sometimes it is not, regardless of whether a...
  21. Replies
    11
    Views
    14,934

    In this situation, the miniwiggler connection...

    In this situation, the miniwiggler connection light is flashing but DAS refuses to close the connection. The error message is completely wrong from any perspective.

    1352
  22. Replies
    11
    Views
    14,934

    My poor first impressions of the DAP miniwiggler...

    My poor first impressions of the DAP miniwiggler and DAS are only being further confirmed the more I use them. They are so flaky on Windows 8.1 and are seriously wasting my time.

    Numerous times,...
  23. Replies
    11
    Views
    14,934

    Jackson, So the one LED that lights up does...

    Jackson,

    So the one LED that lights up does not indicate a connection? Is it simply detecting voltage? I noticed that if the debug lines were backwards it was off. I think that my chip must be...
  24. Replies
    11
    Views
    14,934

    Hi Jackson, Thanks for the details so far. ...

    Hi Jackson,

    Thanks for the details so far.

    I understand the need to have UDAS running, but what I don't understand is the meaning of the LEDs on the miniwiggler. I think I need to know this to...
  25. Replies
    11
    Views
    14,934

    Jackson, I need more information. It would...

    Jackson,

    I need more information. It would help if you answered my original questions as most of the information I have seen in the forums is incomplete like this, assuming familiarity with the...
Results 1 to 25 of 88
Page 1 of 4 1 2 3 4
Disclaimer

All content and materials on this site are provided “as is“. Infineon makes no warranties or representations with regard to this content and these materials of any kind, whether express or implied, including without limitation, warranties or representations of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, whether express or implied, is granted by Infineon. Use of the information on this site may require a license from a third party, or a license from Infineon.


Infineon accepts no liability for the content and materials on this site being accurate, complete or up- to-date or for the contents of external links. Infineon distances itself expressly from the contents of the linked pages, over the structure of which Infineon has no control.


Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Usage Terms of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Usage Terms of this site. Infineon reserves the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.