infineon4engineers Facebook

infineon@google+ Google+

infineon@linkedin linkedin

infineon4engi@twitter twitter

infineon@youtube youtube

Search:

Type: Posts; User: MoD

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    382

    For programming you need an interface like this...

    For programming you need an interface like this ones, only a single device is not possible:
    https://www.ehitex.de/en/accessories/2505/dap-miniwiggler-v3
    or...
  2. Thread: .elf and

    by MoD
    Replies
    6
    Views
    264

    Hi, a .hex file contains only the values for...

    Hi,
    a .hex file contains only the values for different memories and will be used for programming of the device (e.g. via Memtool).
    A .elf file contains, additional to the memory informations, debug...
  3. Thread: QSPI0 for TC399

    by MoD
    Replies
    7
    Views
    332

    You can find all information here:...

    You can find all information here:
    https://myicp-dmz.extra.infineon.com/SitePages/Home.aspx
    If not yet done then registration is needed.
  4. What you mean with undef instruction access? If...

    What you mean with undef instruction access? If the debugger shows undef as assembly code then maybe the debugger don't know the instruction.
  5. Replies
    3
    Views
    192

    Hello, what is the state of ESR0 when stops?...

    Hello,
    what is the state of ESR0 when stops? When it is low (evaluation board has a red led connected to advice), then the device is in reset and I maybe you have a problem with the safety watchdog...
  6. Hi, you must initialize the register with a mtcr...

    Hi,
    you must initialize the register with a mtcr instruction, also SYSCON. More information about memory protection (register description) you can find in the architecture manual part 1 chapter 9....
  7. Replies
    1
    Views
    515

    Please check the iLLD demos. You can find there...

    Please check the iLLD demos. You can find there the ScuEruDemo. This should help.
  8. Replies
    2
    Views
    386

    There exist different steps of this device which...

    There exist different steps of this device which have different registers. Please check that the datasheet (register description) is for this step.
  9. Thread: TC27x MultiCAN

    by MoD
    Replies
    4
    Views
    406

    Config seems be good. Check the output P20.8 when...

    Config seems be good. Check the output P20.8 when you send anything on this node. Because you set also node 1 you will use there P14.0/P14.1. If the IO config for P14.0/P14.1 is also correct?
    You...
  10. Thread: TC27x MultiCAN

    by MoD
    Replies
    4
    Views
    406

    Hi, you must configure the P20.8 as output of...

    Hi,
    you must configure the P20.8 as output of TXDCAN0 (P20.IOCR8) and P20.7 as input for RXDCAN0A (P20.IOCR4).
    Addtional the PDR Register for P20.8 should be set to the needed output strength...
  11. Replies
    8
    Views
    698

    This version is very old. I don't know if there...

    This version is very old. I don't know if there was a problem on this version. Download the latest iLLDs from myicp (V1.0.1.9.0), maybe this solve the problem.
  12. Replies
    8
    Views
    698

    The function IfxMultican_Can_Node_init calculate...

    The function IfxMultican_Can_Node_init calculate the needed settings for the needed baudrate. If you have later then 2x your baudrate then maybe the CCUCON1.CANDIV is changed after Can_Node_init. You...
  13. Replies
    8
    Views
    698

    Which code you are using? How you configure?

    Which code you are using? How you configure?
  14. Replies
    3
    Views
    390

    Check the user manual of TC29xB, there is a EMEM...

    Check the user manual of TC29xB, there is a EMEM chapter.
  15. Replies
    8
    Views
    698

    Change the baudrate in your code to the needed...

    Change the baudrate in your code to the needed CAN speed. 250000 bit/s are no problem for the device. How your software calculate the baudrate?
  16. Replies
    1
    Views
    454

    Maybe it is possible but not recommended. Before...

    Maybe it is possible but not recommended. Before write you should make sure that the sector is already erased, by erasing the sector or by checking the sector via Verify Erased Logocal Sector. This...
  17. Replies
    3
    Views
    390

    First you must unlock the EMEM (see EMEM...

    First you must unlock the EMEM (see EMEM documentation). After this you must initialize the memory (e.g write 0 to all locations), because also the EMEM is ECC protected and after power on there is...
  18. Replies
    1
    Views
    516

    I forwarded your hint to the responsible...

    I forwarded your hint to the responsible department for check and improvement.
  19. Replies
    3
    Views
    430

    The IOV indicate that an Interrupt Overflow is...

    The IOV indicate that an Interrupt Overflow is detected. This means that you lost the previous interrupt. This can be happen if you have a timer and the interrupt of this timer happens second time...
  20. As long as the timer interrupt has a higher...

    As long as the timer interrupt has a higher priority than the spi interrupts are the spi interrupts ignored until the timer interrupt is exited. After enabling the interrupts in the timer interrupt...
  21. Replies
    4
    Views
    382

    With the FT232HL this will not work. You need...

    With the FT232HL this will not work. You need such a device as interface: https://www.ehitex.de/en/accessories/2505/dap-miniwiggler-v3 or...
  22. Replies
    2
    Views
    449

    The nested one is not handled because the...

    The nested one is not handled because the interrupts are disabled when the device jumps in the interrupt vector table. If you will allow nested Interrupts then your interrupt service routine must be...
  23. Replies
    1
    Views
    718

    You can't read the TX FIFO. The DATAENTRY...

    You can't read the TX FIFO. The DATAENTRY register is a write only register. If yiu read the RXEXIT register then you get the next available value from the receive FIFO if there is anything available.
  24. Replies
    1
    Views
    278

    Why you don't use the receive interrupt of QSPI2?...

    Why you don't use the receive interrupt of QSPI2? External IRQ is not necessary.
  25. Check ESR0, if ESR0 is always low then the device...

    Check ESR0, if ESR0 is always low then the device is damaged and can't be recovered. Otherwise when ESR0 is high then the device is in the Generic BSL and you should connect the device via the BSL to...
Results 1 to 25 of 42
Page 1 of 2 1 2
Disclaimer

All content and materials on this site are provided “as is“. Infineon makes no warranties or representations with regard to this content and these materials of any kind, whether express or implied, including without limitation, warranties or representations of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, whether express or implied, is granted by Infineon. Use of the information on this site may require a license from a third party, or a license from Infineon.


Infineon accepts no liability for the content and materials on this site being accurate, complete or up- to-date or for the contents of external links. Infineon distances itself expressly from the contents of the linked pages, over the structure of which Infineon has no control.


Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Usage Terms of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Usage Terms of this site. Infineon reserves the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.