infineon4engineers Facebook

infineon@google+ Google+

infineon@linkedin linkedin

infineon4engi@twitter twitter

infineon@youtube youtube

Search:

Type: Posts; User: UC_wrangler

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    78

    Hi SmileOn. The challenge here is that the RIF...

    Hi SmileOn. The challenge here is that the RIF only supports the RXS and similar external ADCs.

    You can get up to 2.4 MSPS out of the EVADC, but I'm guessing that for your application, you need...
  2. Thread: .elf and

    by UC_wrangler
    Replies
    6
    Views
    263

    Hi KDN. Where is your application - in PFLASH,...

    Hi KDN.

    Where is your application - in PFLASH, or in RAM? When you say the controller doesn't retain its code, what address are you looking at to know it's gone?

    Do you have boot mode headers...
  3. Replies
    1
    Views
    100

    Hi vvssg. Instead of inventing a whole new API,...

    Hi vvssg. Instead of inventing a whole new API, have you tried using the sample code from the iLLD? In the help file (under Modules -> MULTICAN -> How to use the CAN Interface driver), there's a...
  4. The TC26x only contains a logic-level PSI5...

    The TC26x only contains a logic-level PSI5 interface. There is no direct PHY for PSI5 on the AURIX.
  5. Thread: .elf and

    by UC_wrangler
    Replies
    6
    Views
    263

    Is your code targeting RAM...

    Is your code targeting RAM (0x50000000-0x700FFFFF), or flash (starting with 0x8 or 0xA)? If it's running from RAM, that would explain why the AURIX doesn't retain it through a power cycle ;)
  6. Replies
    1
    Views
    96

    Hi VVSS. For PFLASH, the erased state (all 0s)...

    Hi VVSS. For PFLASH, the erased state (all 0s) always causes an uncorrectable ECC read error.

    An erase is only necessary before a write if the destination is not already erased.

    For example:...
  7. Replies
    4
    Views
    3,392

    Hi Pirate02. The IfxCpu_Perf functions are part...

    Hi Pirate02. The IfxCpu_Perf functions are part of Infineon's Low Level Device (iLLD) driver library. Add those to your project and then try something like this:



    #include "IfxCpu.h"

    void...
  8. Replies
    2
    Views
    173

    Hi Lukas_G. The nodePointer array configures how...

    Hi Lukas_G. The nodePointer array configures how each CAN node's service requests are sent to the Interrupt Router. It's used inside of IfxMultican_Can_initModule():


    /* Configure interrupt...
  9. Hi rivaldo01. You can set the bit timing to be...

    Hi rivaldo01. You can set the bit timing to be driven by the oscillator directly with this function:


    IfxMultican_setInputClock( mcanSFR, IfxMultican_ClockSelect_fosc0 );

    But this is one area...
  10. Hi Mattias. You can modify your iSystem...

    Hi Mattias. You can modify your iSystem initialization file to set up the debug system so that the watchdog system is still active when the debugger is connected, and when the CPU hits a breakpoint,...
  11. Replies
    7
    Views
    326

    @MoD I think you meant to post the public link ;)...

    @MoD I think you meant to post the public link ;)

    https://myicp.infineon.com/SitePages/Home.aspx
  12. Hi Specimen. The AURIX NBTRx isn't the same as...

    Hi Specimen. The AURIX NBTRx isn't the same as Vector's BTR0 and BTR1 registers. Just make sure the sampling point and baud rate is the same. SJW=2 is probably your best bet.

    In your last...
  13. Hi specimen. Yes, I should have said...

    Hi specimen. Yes, I should have said samplePoint=7500 :)

    Working backwards from NBTR=0x3EC9, only the sample point needs some tweaking (but it's probably close enough to work):

    - BRP=9 means:...
  14. Hi Specimen. The Vector tool shows the bit...

    Hi Specimen. The Vector tool shows the bit timing information in a fancy graphical way. Compare that to Figure 21-12 CAN Bus Bit Timing Standard on page 1641 of tc23x_tc22x_um_v1.1.pdf:
    - Sync Seg...
  15. Replies
    1
    Views
    203

    Hi Lukas_G. There's a demo for the ERU in the...

    Hi Lukas_G. There's a demo for the ERU in the latest iLLD - see ScuEruDemo, \0_Src\AppSw\Tricore\Demo_Illd\ScuEruDemo.c.

    To use ESR1 as a wakeup, try setting ESR1 as a wakeup...
  16. Hi Rombic. Try enabling the On-Chip Debug System...

    Hi Rombic. Try enabling the On-Chip Debug System with this sequence first:



    #include "IfxCbs_reg.h"

    // Unlock debug system if it's not already unlocked
    if( !(__mfcr(CPU_DBGSR) &...
  17. Hi specimen. What CAN bit timing parameters are...

    Hi specimen. What CAN bit timing parameters are you using on the Vector side? By default, the iLLD uses these parameters - see IfxCan_Can_initNodeConfig in IfxCan_Can.c:

    .baudRate ...
Results 1 to 17 of 17
Disclaimer

All content and materials on this site are provided as is. Infineon makes no warranties or representations with regard to this content and these materials of any kind, whether express or implied, including without limitation, warranties or representations of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, whether express or implied, is granted by Infineon. Use of the information on this site may require a license from a third party, or a license from Infineon.


Infineon accepts no liability for the content and materials on this site being accurate, complete or up- to-date or for the contents of external links. Infineon distances itself expressly from the contents of the linked pages, over the structure of which Infineon has no control.


Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Usage Terms of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Usage Terms of this site. Infineon reserves the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.