infineon4engi@twitter infineon4engineers infineon@linkedin infineon@youtube
twitter Facebook Linkedin Youtube

Search:

Type: Posts; User: Srivatsa

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Hi, when the EN pin is pulled low the output...

    Hi, when the EN pin is pulled low the output state of the gate driver will be in high impedance mode.
  2. Replies
    3
    Views
    756

    What is the deadtime between HIN and LIN? Try...

    What is the deadtime between HIN and LIN? Try with a delay between the two and with 50% duty cycle, LIN first and then HIN.
    Try removing the RC across the MOSFETs and the RC at the load L.
  3. Replies
    3
    Views
    756

    Hi, You can provide an initial value to the...

    Hi,

    You can provide an initial value to the bootstrap capacitors C17, C23 and check if the error is resolved.

    Thanks.
  4. Replies
    3
    Views
    2,109

    Yes. The IC biasing conditions including the VCC...

    Yes. The IC biasing conditions including the VCC should be met with the rectifier. See below application notes:
    ...
  5. All these can provide 2 A continuous drive...

    All these can provide 2 A continuous drive current. The 2ED - F2 will not be able to deliver 5 V since the undervoltage lockout of the secondary side is set at 12 V. Hence minimum the recommended...
  6. Replies
    3
    Views
    2,109

    The IRS2453D is a full bridge gate driver based...

    The IRS2453D is a full bridge gate driver based on the IR2153D self-oscillating half-bridge gate driver IC.
  7. Replies
    1
    Views
    2,040

    From the schematic it is a transformer as there...

    From the schematic it is a transformer as there is no need for energy storage.
  8. Replies
    4
    Views
    2,289

    They are arbitrary examples used to test at close...

    They are arbitrary examples used to test at close to 100 kHz switching frequency.

    Isolated gate drivers can go to 1 MHz, level-shift gate drivers are limited to around 300 kHz to 500 kHz as level...
  9. Replies
    4
    Views
    2,289

    The Electrical Characteristics table provides the...

    The Electrical Characteristics table provides the test condition for the Max. Oscillator Frequency as Ct = 1 nF and Rt = 7.43 kΩ giving 106 kHz. For the minimum recommended values of Ct = 330 pF and...
  10. Replies
    4
    Views
    4,804

    Hi Marcel, The complementary pair easily...

    Hi Marcel,

    The complementary pair easily provides fast turn on and turn off characteristics.

    Pls look here...
  11. Replies
    4
    Views
    4,804

    Hi Marcelo, The 1ED020I12-B2 has max driving...

    Hi Marcelo,

    The 1ED020I12-B2 has max driving current of 2 A and it cannot drive 3 FF200R12KT4 IGBTs on its own. It will need external booster stage as shown in page 11 here...
  12. Thread: 2ed21094s06j

    by Srivatsa
    Replies
    4
    Views
    3,904

    Hi Ajay, It's not clear to me where the...

    Hi Ajay,

    It's not clear to me where the Negative terminal of input power supply should be connected: The Negative power supply should be connected to the Vss (pin 5). Vss (pin 5) and COM (pin 6)...
  13. Replies
    3
    Views
    2,572

    Hi, Pls try with one of the below channels: ...

    Hi,

    Pls try with one of the below channels:

    https://www.infineon.com/cms/en/about-infineon/company/contacts/product-support-form/?redirId=56193

    Live Chat @...
  14. Replies
    3
    Views
    2,572

    Hi, As this is an automotive grade driver IC,...

    Hi,

    As this is an automotive grade driver IC, kindly contact your regional Infineon team for direct support.

    Thanks and regards,

    Srivatsa
  15. Thread: 2ed21094s06j

    by Srivatsa
    Replies
    4
    Views
    3,904

    Hi Ajay,. Thanks for using the 2ED21094S06J in...

    Hi Ajay,.

    Thanks for using the 2ED21094S06J in your design. Our answers are as below:

    Vcc (input power supply) is supply for both internal logic and low-side gate driver. Typical connection...
  16. Hi, Kindly contact your regional Infineon team...

    Hi,

    Kindly contact your regional Infineon team for support on the automotive grade gate driver - 1EBN1001AE.

    Thanks and regards,

    Srivatsa
  17. Hi, The tool is available for download at...

    Hi,

    The tool is available for download at Bootstrap Capacitor Excel Tool.

    Best regards,

    Srivatsa
  18. Replies
    2
    Views
    1,162

    Few general guidelines: 1. Capacitor on Vcc...

    Few general guidelines:

    1. Capacitor on Vcc should be atleast 10 times capacitor on VB. Say Vcc cap = 10 uF, VB cap = 1 uF. This will ensure the bootstrap capacitor gets charged during transients....
  19. Replies
    5
    Views
    1,924

    Girish, BTN8982TA can operate upto 40 V only....

    Girish,

    BTN8982TA can operate upto 40 V only. I'm not familiar with IP76 rating. Guessing you meant IP67, you can start with calculating the power loss in each device. I believe you wont be using...
  20. Replies
    5
    Views
    1,924

    Hi, Infineon's TLE family of solenoid drivers...

    Hi,

    Infineon's TLE family of solenoid drivers are suitable for driving solenoids. You can look at TLE9104SH for your application. This comes from our automotive portfolio and for further support...
  21. Replies
    2
    Views
    2,075

    We checked on the 6EDL internal connections and...

    We checked on the 6EDL internal connections and our feedback is as below:

    1) There is no connection to those NC pins, however we do not recommend to use those NC pins since there could be...
  22. Replies
    11
    Views
    4,837

    For reducing the current spikes, you can check...

    For reducing the current spikes, you can check your layout. See an optimal layout example as attached. Use dedicated traces right from the shunt resistor to the resistors of
    amplifier. Traces must...
  23. Replies
    11
    Views
    4,837

    Pls check if the MOSFET Q8 is turning ON. Also,...

    Pls check if the MOSFET Q8 is turning ON. Also, check the status of Fault pin. You can write to me at srivatsa.raghunath@infineon.com and I will see if I can get a field applications engineer to...
  24. Replies
    11
    Views
    4,837

    The 82 ohm is not needed in actual application....

    The 82 ohm is not needed in actual application. You are using it to charge the bootstrap capacitor which provides HO output. Ideally when LO turns on the low side MOSFET, the bootstrap capacitor...
  25. Replies
    11
    Views
    4,837

    Please share your schematics.

    Please share your schematics.
Results 1 to 25 of 53
Page 1 of 3 1 2 3
Disclaimer

All content and materials on this site are provided “as is“. Infineon makes no warranties or representations with regard to this content and these materials of any kind, whether express or implied, including without limitation, warranties or representations of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, whether express or implied, is granted by Infineon. Use of the information on this site may require a license from a third party, or a license from Infineon.


Infineon accepts no liability for the content and materials on this site being accurate, complete or up- to-date or for the contents of external links. Infineon distances itself expressly from the contents of the linked pages, over the structure of which Infineon has no control.


Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Usage Terms of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Usage Terms of this site. Infineon reserves the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.