infineon4engineers Facebook

infineon@google+ Google+

infineon@linkedin linkedin

infineon4engi@twitter twitter

infineon@youtube youtube

Search:

Type: Posts; User: WoS

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    1,474

    I suppose you refer to this programming...

    I suppose you refer to this programming description:
    https://www.infineon.com/dgdl/Infineon-TLE4997-UM-v01_00-EN.pdf?fileId=5546d4625d5945ed015d9e2be09550ff

    Agreed, the problem is not at all the...
  2. Replies
    2
    Views
    1,467

    This question is not really related to the sensor...

    This question is not really related to the sensor as such. I think it is a more general questions about how magnetic fields look like around moving magnets (a general physics topic)...
    The 3D sensor...
  3. Replies
    4
    Views
    2,457

    In your schematic you have not shown the pin...

    In your schematic you have not shown the pin numbers. Just for clarification:
    The "main GND" is pin 3 on the sensor (see table 2 of the datasheet). If this is connected i2c should work already. even...
  4. Replies
    5
    Views
    3,663

    The sequence "Start - 0x00 - Stop" (which is...

    The sequence "Start - 0x00 - Stop" (which is basically sending just the general call address 0 on the i2c bus) resets the sensor at the end of the frame.

    Is SDA on low on intention during...
  5. Replies
    1
    Views
    1,260

    Had a quick look. Configuration parity in the W2...

    Had a quick look. Configuration parity in the W2 device has to be calculated as:
    * all bits of i2c registers 0x07 to 0x0C
    * 7 LSB of i2c register 0x0D (so the WU enable flag is also part of the...
  6. The issue happened again and I think I know the...

    The issue happened again and I think I know the reason now.

    Yesterday was working on a newly set up project, all working well - including debugging.
    Over night the PC was in standby, debugger was...
  7. Replies
    3
    Views
    4,238

    Just setting "debug" as build configuration gives...

    Just setting "debug" as build configuration gives you a bunch of settings related to this configuration - but you can set/change them to whatever you want, even to generate code w/o debugging in....
  8. Replies
    5
    Views
    2,241

    Maybe it is just disabled? You may try following:...

    Maybe it is just disabled? You may try following:
    Select in Eclipse menu: "Window" -> "Customize Perspective..."
    From this dialog, select "Tool Bar Visibility" and click on "toolbar", then click...
  9. I removed DAVE and JLINK completely (including...

    I removed DAVE and JLINK completely (including the Infineon folder generated in the user home and the workspaces - of course after checking everything in / back-up of files).
    Then I did the reboot...
  10. Good point, marzoel. I am running a 32bit...

    Good point, marzoel.

    I am running a 32bit version from the very beginning - for the old and the new setup - on a 64bit Win7 (as seen above: "--host=i686-w64-mingw32") - especially because the...
  11. Noticing the same problem. Got a new computer and...

    Noticing the same problem. Got a new computer and did a setup using the latest DAVE v4 download (Version 4.3.2 as I can find in the "about dave" screen).
    Even with setting up a brand new (default)...
  12. Replies
    2
    Views
    5,584

    I think I discovered an other bug in the XMC lib?...

    I think I discovered an other bug in the XMC lib?

    In my above example, EXS2B of ERU0/EXISEL should be set to one after calling "XMC_ERU_ETL_Init(ERU0_ETL2, &p2_11_int_event_generator_config)". So...
  13. Replies
    2
    Views
    5,584

    Pin interrupt on XMC1 (via XMC Lib) not working

    Hi all,

    got another issue. For completeness: I am using the xmc 2go board for this experiments.

    I'd like to call a handler (toggling a LED) each time the pin P2_11 receives a falling edge.
    So...
  14. Replies
    10
    Views
    11,863

    When looking at my example (the "main.c" file),...

    When looking at my example (the "main.c" file), just add this before the XMC_UART_CH_Start() line:



    /* enable receive interrupt */
    XMC_UART_CH_EnableEvent(XMC_UART0_CH0,...
  15. Replies
    10
    Views
    11,863

    Thanks, got it. Yes, the GPIO mode function in...

    Thanks, got it. Yes, the GPIO mode function in the lib does not handle the analog/digital switching, :(
    XMC_GPIO_Init() is a much cleaner approach as well.



    /* (very) simple example for "XMC...
  16. Replies
    10
    Views
    11,863

    Hello and thanks for your quick response! As...

    Hello and thanks for your quick response!

    As mentioned, I am trying to evaluate DAVE v4 and its xmclib with the XMC2go and get something working with it, I have a functional solution in DAVE v3...
  17. Replies
    10
    Views
    11,863

    xmc2go and xmclib for UART in dave 4 ?

    As the xmc2go does not work with the UART app in DAVE v4 yet, I tried an alternate approach using the XMC lib in DAVE v4.
    I used "simple main project" and selected the XMC1100 in the VQFN24 package...
Results 1 to 17 of 17
Disclaimer

All content and materials on this site are provided “as is“. Infineon makes no warranties or representations with regard to this content and these materials of any kind, whether express or implied, including without limitation, warranties or representations of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, whether express or implied, is granted by Infineon. Use of the information on this site may require a license from a third party, or a license from Infineon.


Infineon accepts no liability for the content and materials on this site being accurate, complete or up- to-date or for the contents of external links. Infineon distances itself expressly from the contents of the linked pages, over the structure of which Infineon has no control.


Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Usage Terms of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Usage Terms of this site. Infineon reserves the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.