Welcome to the Infineon Developer Community

i'm trying SPI_CPU_1_KIT_TC334_LK.. I've joined SPI_A to SPI_B (confirmed on schematic for dev kit - - i hope).

when the code runs i dont have an LED on which says the data has transfered ok -- 😞 .. sad face .

i've run it a few times and set a break point . plus used a logic analyser ..

if i disconnect the MISO / MOSI lines i receive no data .. so i know the SPI slave is getting data..  .. 

i've added this line , but nothing has changed .. 

Where are CAD models for QDPack.

There are .pdf files at https://www.infineon.com/cms/en/product/packages/PG-HDSOP/PG-HDSOP-22-1/ These are NOT CAD models.

STEP form would be preferred.

Greg

My radar is Distance2GoL.

I reconfigure the firmware in config.h, make the one frame is 40ms,  each frame has 10 pulses, and each pulse lasts 2ms.

First when I charge the board and use OSC to watch it's TX_EN, everything is finr just like I set. Here is the picture of the TX_EN:

But, when I start use matlab to acquire the raw data, when I run the matlab code, it has been changed.

Here is the TX_EN when I start to rum the matlab code:

Please tell me why this matlab code just for acquire the raw data will affect the radar, what should I do to modify the matlab code? 

I am looking for a Power MOSFET. I need a Silicon (Si) transistor with high Vds >500V, but I don't know how to find the transistor I need. The list on the website doesn't state transistor material. Please help. 

Hi ,
 We are working on FX3 cypress CYUSB3014  and using TI (Texas Instrument ) image file to  configure the FX3 . Using Streamer application  we checked the throughput , achieved 256300 KBps . We need to achieve maximum speed around 4Gps . Please help us to achieve this speed and please  suggest correct image file also to achieve the same .

My purpose is to control the private server motor. Because most servo motors are controlled using pulses. So if it involves the acceleration and deceleration of the motor, the interval between each pulse may be different. Therefore, every time the timer is interrupted, the entry time of the next timer will be changed. In STM32, I can make the time into a list. Then directly import the register TIM3->ARR = tim[X]. However, it was found that in XMC1302, it is not allowed to write values directly to the register. But need to use

TIMER_Stop(&TIMER_0);
status = TIMER_SetTimeInterval(&TIMER_0, tim[ X ]);
if (status == TIMER_STATUS_SUCCESS)
{
        TIMER_Start(&TIMER_0);
}

This is how you can reset it. But this code runs too slowly. About 60US. This is obviously too long. Is there a faster way?

你好，我想问一下，串口如果使用DMA模式的话，有什么方法可以让我获得串口接收到的数据，除了函数getbuffer以及DMA通道回调事件触发的时候能够获得其handle的buffer。这两种方法虽然可以得到串口收到的数据，但是如果之前配置的缓存区没有满的话，我们是拿不到buffer，因此也拿不到他的数据。
此外，我也用了CyU3PDmaChannelSetWrapUp函数，能够在DMA通道缓存区未满时将其强制提交，从而获得缓存区。这个方法虽然好，但是我用一个线程任务专门执行这个函数，它竟然有次数限制，当超过了某一个次数的时候，它就不再使用，这是怎么回事呢？

Dear Infineon team,
the spice model of the IMZA120R014M1H and other models in the same .lib file are incompatible with SPICE.
In LTSPICE the program repots: "ERROR: Node U1:$M009F:$M01LF:N03D6 is floating and connected to current source G:U1:$M009F:$M01LF:01NW".
The VCCSs G01NW and G01O5 have specified 2 nodes and a value. A VCCS needs to be specified with 4 nodes, correct?
Is there a fix for this issue?

Hi Expertises,

In TLE9012 DQU chapter 17 mentioned that "Cell voltage supervision warning flags CELL_UV_DAC_COMP" and "Cell voltage supervision warning flags CELL_OV_DAC_COMP" can detect overvoltage and undervoltage. Is it the same as cell_UV and cell_OV?

Where could I find more details for CELL_UV_DAC_COMP and CELL_OV_DAC_COMP?  Would someone explain that how to operate and set?

Thanks

1.请问我在官网上看到了，伺服电机的方案。

2.请问这个方案是否开放？

3.如果开放能获得那些资料。

Whitepaper_CoolSiC™ – The_perfect_solution_for_servo_drives_EN (infineon.com)