Featured Discussions
Dear Sir,
I need an AUX power under 10W ,3.3V application which Input DC Vin 150V.
I saw the Coolset product - EVAL-ICE2QR1765Z. (provide a voltage of 70VDC to 380 VDC depending on the mains input voltage.)
Input voltage 85Vac~265Vac
Input frequency 50Hz, 60Hz
Output voltage and current 5V 2A
Output power 10W
can I follow the EV kit of EVAL-ICE2QR1765Z and take off bridge rectifier BR1 to work with input VDC at 150V?
thanks.
Show Less
I refer to someone else's project on the Internet, but after loading it in, I found that I can't find any of its header files, how should I add the path to the header files?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/%E8%B6%85%E9%AB%98%E9%80%9FUSB%E5%A4%96%E8%AE%BE/FX3%E5%B7%A5%E7%A8%8B%E5%AF%BC%E5%85%A5%E5%A4%B4%E6%96%87%E4%BB%B6%E6%89%BE%E4%B8%8D%E5%88%B0%E6%8A%A5%E9%94%99/td-p/742868
Show LessNow we can modify the source pdo use dpm_update_src_cap() , CCG5 send source capability to device, and we want to know if there is any function can get the rdo from device
Show LessI set up a new project to test the MCU 4700. And I try to use P2.8 output a high level, because according to your user manual that P2.8 is not connected to any signal.
Here is my testing firmware:
However, it still does not work, I can't test a high level in P2.8.
Could you please tell me what' going on here?
Show LessIn the LE GATT Server Throughput Example, I found that the size of each notify array is 244u. I want to know if the maximum size of the notify data is 244 arrays. Because I want to notify 512 or 1024 each time to reduce the pressure on my streambuffer in FreeRtos. If notify supports arrays with a notification size greater than 244 each time, what modifications do I need to make to achieve arrays with a notification size of 512 or 1024 each time.
Show Less
Hi there,
May i confirm if cyw20704 is BT/BLE 5.0 because some docs say it's a BT/BLE 5.2, thank you!
Mason
请问IM241-M6T2B的电流采样电路:N(U/V/W)引脚到ITRIP引脚这之间的电路对应着数据手册的推荐而搭建,那么应该选择什么样的参数呢?
i need BMU for honda ens:1. part number RB0067A1V01. BMUN6220159. how can i buy it in China? please.
Hello everyone! There are a couple of phenomena regarding the parameterization of the motor for actual debugging, and I'd appreciate any advice.
1. Startup duty cycle, more than 35% or more, a large number of tests, there will be a probability of power-on direct overcurrent protection, and then the system strike, restart to work properly;
2.Kp Ki parameter design, as if there is not much law, according to Kp/Ki = L / R, this formula does not seem to be very right, because in general, L is particularly small, so must be too large a difference, is not a 2:1 relationship, but at present the test to see how to set up, will only affect the corresponding speed, the motor running stability has not been found to have any effect. Regarding the pi parameter, if there is any opinion, please point it out.
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/MOTIX-MCU/%E7%94%B5%E6%9C%BA%E5%8F%82%E6%95%B0%E8%AE%BE%E7%BD%AE/td-p/742823
Show Less