Featured Discussions
Dear team
I would like to use the MA5302 to create a single-supply, single-ended input stereo amplifier.
There was an evaluation board for MA5302 with positive and negative power supplies and single-ended input, but this does not seem to be compatible with a single power supply.
Therefore, I am thinking of creating a circuit for 2 channels using the evaluation board below as a reference.
https://www.infineon.com/cms/jp/product/evaluation-boards/ref_ma5332btlsps/
I have two questions regarding the above.
① Does the supply voltage need to be +40V?
Since I only need to be able to get an output of about a few tens of W, I would like to first make a simple evaluation using a commercially available switching power supply.
(If possible, we would like to be able to evaluate by inputting 30V or less.)
② If I use a single power supply, do I need to make the audio input differential?
I would like to use single-ended input if possible.
Best Regards,
TOMMAT
Show LessHi,
Can you please advise if the CYW20829B0-P4 module supports Zephyr? If not, is there any plan for that?
Regards,
Marcelo Macedo - FAE at Neutronics
Show LessHello,
we ported the wifi stack in our new product, it has a WiFi stability issue, mainly it shows SDIO bus communication error, we made a restart stack when it happened but we don't know where is the root cause, can you help us with this?
Thank you very much!
- setup
- pack: https://github.com/Infineon/AIROC-Wi-Fi-Bluetooth-STM32
- module/chipset: COMPONENT_4373/COMPONENT_MURATA-2AE
- after connecting to AP, send a request to fetch RSSI every 5 seconds
- WHD/WCM logging enabled
- host MCU:STM32H7B3LI, interface by SDIO
- RTOS: ThreadX
- issue
- got an error on "SDIO bus failed to come up , whd_kso_enable failed" from time to time, sometimes shows up just after connecting to AP, and sometimes happens a few minutes after
- few changes from the stack but no improvement:
- force speed as 25MHz ( not jump to 50MHz)
- force to use memory copy to internal RAM for DMA () -- bool "use_temp_dma_buffer = true"
- #define CYBSP_WIFI_SDIO_NEEDS_INIT (0)
- some timing/retry change to long
- #define SDIO_ENUMERATION_TRIES (1000)
#define SDIO_RETRY_DELAY_MS (2)
#define SDIO_BUS_LEVEL_MAX_RETRIES (200) - #define SPINWAIT_POLL_PERIOD 20
- #define KSO_WAIT_MS (2)
#define MAX_KSO_ATTEMPTS (1000)
- #define SDIO_ENUMERATION_TRIES (1000)
We have been working on debugging an issue where the TC29x Ethernet receiver halts after being saturated with messages and the Ethernet module must be restarted for the receiver to continue receiving messages. We have seen this behavior on two of our designs and on the TC2X9 Triboard. In debug mode the Receive Watchdog Timeout bit causes an interrupt and data corruption is seen when reviewing the Rx buffers. This eventually leads to the receiver halting, no longer receiving any messages and the missed FIFO counter being filled with the missed messages. We are trying to determine the root cause of the data corruption and the halting of the receiver. Any help on this would be greatly appreciated.
Note, with our current test configuration we have also seen that disabling the "Automatic Pad or CRC Stripping" and "CRC Stripping of Type FRAMES" in the MAC configuration prevents the receiver from halting, but we would like to know the root cause of this issue.
Show LessHi Everyone,
Today we are manufacturing sensors using the assembly KMI15/1 manufactured by NXP. We need an alternative because KMI15/1 is obsolete. We are looking at the Infineon #TLE4941PLUSC. The data sheet mentions that it needs a magnet on the back side - that solution is very similar to the KMI15/1. This is a link to the NXP assembly KMI15/1
KMI15/1 Integrated rotational speed sensor (nxp.com)
Can you provide the sensor TLE4941PLUSC (or similar) with that magnet attached to it?
Thank you, it would be great to see your answer.
Show Less
I can program the psoc5 using openocd now, with some caveats. However, if an NVL entry exists, it stops.
I have a project which somehow did something to the NVL.
I understand setting the Reset condition on the Pins can cause this. However, setting the pins to Don't Care doesn't fix this problem, so I suspect something else is causing the NVL to change.
Is there *any* gui / command line interface to find out what is causing the NVL to be set? (so it can be "fixed" in the project?)
This would not normally be a problem, but using openocd to program the psoc halts when the NVL entry is in the Creator generated hex file. I have multiple reasons for using openocd, some of which involve production machines. Others are very fast compile/debug cycle. (https://socmaker.com/?p=1004, and https://socmaker.com/?p=1027)
If I use objcopy, could I exclude that from the elf file for the new obj? (before making a hex file) If so, would it be by address? If so, which address? otherwise, how would I do that exclusion?
Is there a way to use openocd to program the NVL (perhaps kitprog in kitprog mode?) (Just checking)
Thanks!
Show Less
I am working on a wireless charger for electric vehicles and need MOSFET modules for generating the high-frequency AC. The FF3MR20KM1H might fit our application, but I didn't see the forward bias safe operating area plot.
We'd need to handle about 560A with a pulse width of 10.6uS.
Can this module handle this?
Show Less
I am attempting to follow the "Secure Boot" SDK user guide but continually run into the same problem. When attempting to setup the "CySecureTools" workspace i get the same error 'bash: cysecuretools: command not found' i get this even though i installed it and when i attempt to reinstall cysecuretools i got the message stating command already satisfied. This is all done on Windows
Show LessI am implementing a UVC MJPEG application using the FX3 which is sent MJPEG video frame data from an FPGA and we are seeing the following frame corruption. We are currently unsure where to start looking so any help on identifying what might be wrong would be helpful. This is 1080p30 streaming. The video does stream properly for a short while but if there is any moving content on the screen it tends to get corrupted. I have also included a photo of the proper streaming.
Show Less
I plan to port my design from CY7C68013A to CYUSB2014.
Can I use the same development tool and just select the different component?
Are there any potential issues I should be aware of?
Greg
Show Less