Welcome to the Infineon Developer Community

I am designing a power bank with two type C port and two type A port. looking for a integrated four output buck-boost converter so that the chip should support usb power delivery. which chip should i use? also is there any infineon chip where i can do the same but number of inductors will be less than 4? 

For my tail light project, the tail current needs to be 3mA, but I read the specification that the output is 5.62~72mA, with the PWM to do 3mA, may I ask how about the accuracy in this case?

smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/LED-%E9%A9%B1%E5%8A%A8%E8%8A%AF%E7%89%87/TLD7002-%E4%BD%8E%E7%94%B5%E6%B5%81%E7%B2%BE%E5%BA%A6/td-p/743402

I am attempting to follow the "Secure Boot" SDK user guide but continually run into the same problem. When attempting to setup the "CySecureTools" workspace i get the same error 'bash: cysecuretools: command not found' i get this even though i installed it and when i attempt to reinstall  cysecuretools i got the message stating command already satisfied.  This is all done on Windows. 

Hello everyone! Is it possible to directly measure the current running through a DC motor using the BTN9970LV shield? I tried finding the answer in the data sheet and user manual but I was unable to. Thanks for your responses!

Hello,

I have a project that needs to have a frequency connection that takes place at 5”. This connection will complete a circuit. 

What is the best way to do this? Will it be easiest to limit the transmit power and wait for a frequency connection to be detected? This would be easiest with an RFid transmitter I’m sure.

Would it be easiest to have a constant frequency connection between the two components that activate the circuit once the frequency strength reaches a certain strength? I want the tots enclosure to be no more than 1”x1”LxW and .5” in H

I want the simplest most reliable connection method that allows for an activation of a circuit without fail. Please let me know what you think. Call or email me. Thank you.

Jens 

jens@plus4u.plus

(406)672-1783

Hi,

Is any AURIX TC3xx TFT available and compatible with TLE9015DQU_TRX_BRG and TLE9012DQU_DTR_BMS2 evaluation boards?

Regards,

I am trying to load the cyfxuvcinmem_bulk example on my SuperSpeed explorer kit however once I upload the firmware to RAM or I2C, the device does not enumerate as a UVC camera on my laptop. When I last tried a year or so ago, it did work. Is there any known modifications or issues that would prevent the device from enumerating? I am using the cyfxuvcinmem_bulk example taken straight from `<FX3 SDK Install>\firmware\uvc_examples\cyfxuvcinmem_bulk` with no modifications. If I load the LED blink example, the board works as expected.

请教大家一个问题

我现在做的boot程序在跳转app程序的时候，如果boot程序和app程序都没有使用中断的情况下可以正常跳转，但是boot程序或app程序有一方面使用中断的话就会进入到debug，boot程序或app程序单独运行时没有问题。下面按照串口中断举例。

调试状态下会卡在下图位置：

我想知道是哪个地方设置的不对或者少设置了什么地方。

IFX_INTERRUPT(OS_CAT2_General_Handler,0,6);
IFX_INTERRUPT(OS_CAT2_General_Handler,0,5);

why i can't install same handler in different priority. It's logically can do as ARM architecture as the processor only use the priority to get the Handler start, i need a solution for installing the same handler (ISR) in different priorities to handle CAT2 interrupts in my project and i can't upload the project as i have a signed NDA.