Featured Discussions
text.format{('custom.tabs.no.results')}
Hi,
I was going through document AN2358 which suggests an approach to implementing a Manchester decoder.
I have a query about the implementation.
IEEE 802.3 Ethernet standard states that the input data (Manchester encoded) may have a jitter of +-18ns. Now if this is used in a decoder with a fixed delay count (3/4) to sample an input data bit, how will this circuit sample the correct data and produce the recovered output?
Is there any other way this jitter in the input data can be handled to recover the correct data bit?
Thanks
Pulkit
Show Less
Hello,
I want also design the USB3.0 to HDMI use CYPD3120, as described here: Solved: CYPD3120 USB3.0 to HDMI - Infineon Developer Community
But MCDP2900 is not recommended for new design.
Can you recommend me an alternative?
I also found the PS186, but no way to order this chip.
Thanks for an answer
Best Regards
Jakob
Hi
I have downloaded the XMC flasher tool, and when I opened it and tried to connect for the first time I was prompted that there was a new version of the firmware, so I clicked install. But I think somewhere in the installation process it failed, so now the XMC1300 wont connect anymore. I have tried to connect to it using Memtool, but without success.
I have selected device name as 1302-200 (as stated on the chip) and I have selected the connected emulator.
The error log in the XMC flasher is:
INFO-com.infineon.XMCFlasher.MainAppController-main: Logger Name: com.infineon.XMCFlasher.MainAppController
INFO-com.infineon.XMCFlasher.SeggerLibLoad-configureLoad: Not Found property: xmcFlasher.JLink.dllPath Searching in registry key
INFO-com.infineon.XMCFlasher.SeggerLibLoad-configureLoad: Setting property: bridj.JLinkARM.library to: C:\Program Files\SEGGER\JLink_V796e\JLinkARM.dll
INFO-com.infineon.XMCFlasher.SeggerLibLoad-configureLoad: Not Found property: xmcFlasher.JLink.dllPath Searching in registry key
INFO-com.infineon.XMCFlasher.SeggerLibLoad-configureLoad: Setting property: bridj.JLinkARM.library to: C:\Program Files\SEGGER\JLink_V796e\JLinkARM.dll
INFO-com.infineon.XMCFlasher.SeggerDLL-checkAvailabilityAndLoad: Loaded JLink DLL 7.96.e
INFO-com.infineon.XMCFlasher.MainAppController-start: Starting Application in process ...
INFO-com.infineon.XMCFlasher.view.RootLayoutOverviewController-handleChangeDeviceName: Setting Device Name configurations
INFO-com.infineon.XMCFlasher.view.RootLayoutOverviewController-handleChangeEmulator: Setting Device Name configurations
SEVERE-com.infineon.XMCFlasher.ErrorLogCallBack-apply: Communication timed out: Requested 8 bytes, received 0 bytes !
WARNING-com.infineon.XMCFlasher.view.RootLayoutOverviewController-handleConnect: com.infineon.XMCFlasher.DebuggerExceptions: Error get BMI value
INFO-com.infineon.XMCFlasher.view.RootLayoutOverviewController-handleChangeDeviceName: Setting Device Name configurations
What can I do to re-flash it?
I have attached an image of XMC flasher
Show Less您好,我在TL9261芯片的DATASHEET中未看到Node internal delay time的描述,想问一下这个时间应该在哪里查找呢?
Can the dead time of the EVRC driver be adjusted, and if so, where can I find the description of the registers.
Hi all,
I have a induction motor that I am trying to control using the EVAL-M3-IM564 driver board and the EVAL-M3-302F controller board.
I used the MCEWizard to enter all the parameters and generated a .txt file for the MCEDesigner. In the designer I uploaded the .txt file to the controller and tried starting the motor.
Everything goes fine until my RPM reach the "Minimum running speed" RPM value. Then it either stops or runs at 1-10 RPM depending if the previous value was rather small or big. Even if I set the "Minimum running speed" higher than the "Reference speed" parameter in the designer, the motor will keep speeding up beyond the "Reference speed" and shut down when it reaches the "Minimum running speed".
Any idea's what might cause the problem?
PS. I'll add the .mc2 file.
Show LessHello,
I am an engineer who has encountered the issue in the following link while using CX3 U3V.
Solved: CX3 U3V partial buffer - Infineon Developer Community
I have another issue..
Currently, there is an issue where the image is not transmitted occasionally. No error is printed. So, I added a log in the Firmware to print the State of the MIPI Module every 5 seconds. Afterwards, I obtained the following log.
Here are my questions:
- There are cases where it stays in State 15 without any error/action. However, in this case, if I continue to attempt to acquire the image, the image is acquired.
- And suddenly at some point, the State changes to F and after that, no image is acquired at all. In the article below, it seems that if FW_TRG does not become !FW_TRG, it does not move from F. What problem could be causing this?
EZ-USB™ CX3 - USB 3.2 Gen 1 device controller for USB3 Vision camera (infineon.com)
The situation has only changed in the following content from the issue in the above link.
- image size: 1744x2400 -> 872*1200
Thank you
Kang
Show LessI am using IGOT60R070D1 GaN transistor. Can you suggest the Heat sink Part used for this transistor. Hoping for the fast reply
Hello,
I am facing an issue while writing data to the DFlash memory region. I am using the TC375 Flash programming Example code with some changes. Below is the scenario for which I am facing the issue.
1. The first time writing data (0xAF000400) to the address 0xAF000240 is writing successfully.
2. reading data from 0xAF000240 reading successfully.
3. If I write the data that is read from 0xAF000240 to the same address by updating the data with some other value, the memory(0xAF000240) is filling with zeros (0x00000000).
Can any one please suggest the solution.
Thank you very much !
Show Less
Dear Infineon support Team,
I want to replace BTS442 E2 by BTS441RG in one of our products and have following questions:
Most critical for us is the lower maximum allowed Vbb (abs.max) which is 63V for BTS442 and only 43V for BTS441.
The datasheet of the BTS441RG recommends for overvoltage protections 150 Ohm between BTS441.GND and Signal GND. I would like to implement these 150 Ohm but am wondering, if there are any further informations about this replacement:
1) do you have some further informations about replacing BTS442 E2 by BTS441RG not written in the datasheet?
2) Any drawbacks i might currently not be aware of using the 150 Ohm resistor for OV protection as proposed in datasheet?
3) is there a LTspice model for BTS441RG available? For example the BTS436L2G has one on your homepage.
Thank you very much in advance for your support!
Best regards,
Bastian
Show Less