Featured Discussions
text.format{('custom.tabs.no.results')}
大家好,
最近想用keil调试cyt2bt73cae这个芯片的程序,使用mtb导出的工程只有单核应用,然后device这里显示
,这种导出的工程直接是CM4的,编译过后能够达到使用CM0启动CM4的效果?如果不能,我应该怎么做?
当我配置了cm0plus以后,cy_m0p_image[]这个数据的含义是什么,需要我手动调用吗?
当我使用导出的keil工程的GPIO中断时,无法进入终端服务函数,这和我没有CM0有关系吗?
希望有人能够帮到我,感谢~
Show LessThere is said that this bright feet + logo a bit unlike is IR Mexico factory production, I can not judge, please gods look at, this is not authentic, thank you!
Show LessHi,
I would like to know of a sample code to write few bytes to an ISSI 128 MBits of nor flash memory and also basic communication pin andsetup for XMC71000D.
When i setup the memory with xmc7100D at P13 (SCB-SPI) the spi_initialization returns an error. how do i check the device id for this flash memory (ISSI;25LP128- jedec id : [9D6018])
best,
PA
Show LessHi everyone, I am trying to read the battery data from TLE9012DQU without using the default hex file. I have written the following function to send commands and receive data based on UART hello world program. But I am not receiving any data. What am I missing? I am not even able to print anything.
void send_receive_ASCLIN_UART_message(void){
Ifx_SizeT r_count=5;
uint8 transmitData0[1] = {0xaa};
Ifx_SizeT g_count0 = sizeof(transmitData0);
IfxAsclin_Asc_write(&g_ascHandle, transmitData0, &g_count0, TIME_INFINITE); /* Transmit data via TX */
IfxAsclin_Asc_read(&g_ascHandle, g_rxData, &r_count, TIME_INFINITE);
//printf("%x",g_rxData[0]);
uint8 transmitData01[6] = {0x1e, 0x80, 0x3d, 0x00, 0x7f};
Ifx_SizeT g_count01 = sizeof(transmitData01);
IfxAsclin_Asc_write(&g_ascHandle, transmitData01, &g_count01, TIME_INFINITE); /* Transmit data via TX */
IfxAsclin_Asc_read(&g_ascHandle, g_rxData, &r_count, TIME_INFINITE);
//printf("%x",g_rxData[0]);
uint8 transmitData1[5] = {0x1e, 0x80, 0x36, 0x00, 0x01};
Ifx_SizeT g_count1 = sizeof(transmitData1);
//printf("%x\n",transmitData1[0]);
IfxAsclin_Asc_write(&g_ascHandle, transmitData1, &g_count1, TIME_INFINITE); /* Transmit data via TX */
IfxAsclin_Asc_read(&g_ascHandle, g_rxData, &r_count, TIME_INFINITE);
printf("%x %x\n",g_rxData[0],g_rxData[1]);
uint8 transmitData3[5] = {0x1e, 0x81, 0x01, 0x0f, 0xff};
Ifx_SizeT g_count3 = sizeof(transmitData3);
IfxAsclin_Asc_write(&g_ascHandle, transmitData3, &g_count3, TIME_INFINITE); /* Transmit data via TX */
IfxAsclin_Asc_read(&g_ascHandle, g_rxData, &r_count, TIME_INFINITE);
printf("%x %x",g_rxData[0],g_rxData[1]);
uint8 transmitData4[5] = {0x1e, 0x81, 0x0b,0x00,0x00};
Ifx_SizeT g_count4 = sizeof(transmitData4);
IfxAsclin_Asc_write(&g_ascHandle, transmitData4, &g_count4, TIME_INFINITE); /* Transmit data via TX */
IfxAsclin_Asc_read(&g_ascHandle, g_rxData, &r_count, TIME_INFINITE);
printf("%x %x",g_rxData[0],g_rxData[1]);
uint8 transmitData5[3] = {0x1e, 0x01, 0x0b};
Ifx_SizeT g_count5 = sizeof(transmitData5);
IfxAsclin_Asc_write(&g_ascHandle, transmitData5, &g_count5, TIME_INFINITE); /* Transmit data via TX */
IfxAsclin_Asc_read(&g_ascHandle, g_rxData, &r_count, TIME_INFINITE);
printf("%x %x",g_rxData[0],g_rxData[1]);
uint8 transmitData6[5] = {0x1e, 0x81, 0x18,0xee,0x21};
Ifx_SizeT g_count6 = sizeof(transmitData6);
IfxAsclin_Asc_write(&g_ascHandle, transmitData6, &g_count6, TIME_INFINITE); /* Transmit data via TX */
IfxAsclin_Asc_read(&g_ascHandle, g_rxData, &r_count, TIME_INFINITE);
printf("%x %x",g_rxData[0],g_rxData[1]);
uint8 transmitData7[3] = {0x1e, 0x01, 0x24};
Ifx_SizeT g_count7 = sizeof(transmitData7);
IfxAsclin_Asc_write(&g_ascHandle, transmitData7, &g_count7, TIME_INFINITE); /* Transmit data via TX */
IfxAsclin_Asc_read(&g_ascHandle, g_rxData, &r_count, TIME_INFINITE);
printf("%x %x",g_rxData[0],g_rxData[1]);
uint8 transmitData8[3] = {0x1e, 0x01, 0x23};
Ifx_SizeT g_count8 = sizeof(transmitData8);
IfxAsclin_Asc_write(&g_ascHandle, transmitData8, &g_count8, TIME_INFINITE); /* Transmit data via TX */
IfxAsclin_Asc_read(&g_ascHandle, g_rxData, &r_count, TIME_INFINITE);
printf("%x %x",g_rxData[0],g_rxData[1]);
uint8 transmitData9[3] = {0x1e, 0x01, 0x22};
Ifx_SizeT g_count9 = sizeof(transmitData9);
IfxAsclin_Asc_write(&g_ascHandle, transmitData9, &g_count9, TIME_INFINITE); /* Transmit data via TX */
IfxAsclin_Asc_read(&g_ascHandle, g_rxData, &r_count, TIME_INFINITE);
printf("%x %x",g_rxData[0],g_rxData[1]);
}
Show Lesshi, while building the project am getting following error.
make[1]: *** [../mtb_shared/core-make/release-v3.0.3/make/core/build.mk:435: C:/DemoProject/build/CY8C6245LQI/Release/AIController-Psoc6.elf] Error 1
make: *** [../mtb_shared/core-make/release-v3.0.3/make/core/main.mk:376: secondstage_build] Error 2
I tried reinstalling the Modustoolbox, also corrected the path of Environment variable, but nothing seems to be working.
Show LessHi
Is there anywhere I can find S-Parameter models for the the BGSA14GN10 RF switch?
Best regards
您好,各位工程师,我们在测试3KW功率板的时候出现炸机问题,我们猜测是过电压或过电流导致,如何导致的还未确定,请大家能帮忙分析一下。这是什么原因导致的,求解答。
测试环境: 进行电机对拖实验,测试3KW功率板。当测试电机测试到转矩值为95%,NTC温度为100度时,测试电机的功率板发生爆炸。IGBT使用的开关频率是16KHz,母线电压为530V,IGBT是FS35R12W1T7,驱动芯片是IR2214SS,参考的是EVAL-M1-IR2214电路。
下图是损坏的IGBT,六个IGBT都已经损坏变黑,U-H的IGBT中间炸开一个洞,除了V-H的续流二极管损坏,其他续流二极管还是正常的。IGBT的C极与G极未短路。
下图的红色圈子中的是U相的IR2214V,V相的IR2214和W相的IR2214,
黄色圈子中的是下臂的开通、关断、软关断电阻和地上的1R电阻,
绿色圈子中的是上臂的开通、关断、软关断电阻,
蓝色圈子中的是地上打的火光。
下图的红色圈子中的是两个BAT54S-E3-08二极管,
黄色圈子中的是四个BAS16J,115二极管,
绿色圈子中的是U-H、V-H、W-H地上的1R电阻(从右到左)
U相的IR2214的壳体炸开,对应上下臂的BAT54S-E3-08二极管的Pin1出现较为明显的炸开溅射,上下臂地上的1R电阻未损坏。
U-L地下方出现火光,引脚上的锡出现熔化的迹象。
大部分的开通、关断和软关断的电阻损坏阻值变大,Vge之间的10K电阻损坏阻值变小。
四个BAS16J,115二极管都出现损坏,自举电路的二极管也出现损坏。
V相的IR2214的Pin20 HON炸飞,Pin19 Vs烧的发黑,Pin19附近芯片壳体翘起,V-H的220R(软关断电阻)和10R(关断电阻)的电阻表面烧的暗淡变色。
V-H的BAT54S-E3-08二极管的三脚的锡出现熔化,Pin3的壳体出现炸开,V-H地下方出现火光,V-H地上的1R电阻损坏(有灼烧变色的痕迹)。
V-L的BAT54S-E3-08二极管的三脚的锡出现熔化,Pin1翘起,V-L地上的1R电阻未损坏。
V-H的开通、关断和软关断的电阻损坏阻值变大,V-L的开通、关断和软关断的电阻未损坏。
Vge之间的10K电阻损坏阻值变小。
四个BAS16J,115二极管都出现损坏,自举电路的二极管也出现损坏。
W相的IR2214的Pin19 Vs炸飞。
W-H的BAT54S-E3-08二极管的Pin3的壳体被炸开,W-H地上的1R电阻损坏(有灼烧变色的痕迹)。
W-L的BAT54S-E3-08二极管的外壳无明显问题,但是已经损坏,直通,W-L地上的1R电阻未损坏。
大部分的开通、关断和软关断的电阻损坏阻值变大,W-L的Vge之间的10K电阻损坏阻值变小,W-H的Vge之间的10K电阻未损坏。
四个BAS16J,115二极管都出现损坏,自举电路的二极管也出现损坏。
Dear Supporter
I want to translate the following KBA. Please confirm to my work.
General layout considerations for MOSFETs
General layout considerations for MOSFETs - Infineon Developer Community
Regards,
AkUm
Show LessDear Supporter
I want to translate the following KBA. Please confirm to my work.
Temperature dependency of MOSFET parasitic capacitances and losses
Temperature dependency of MOSFET parasitic capacit... - Infineon Developer Community
Regards,
AkUm
Show Less