Featured Discussions
Hi, experts.
When debugging Infineon example "Flash_Programming_1_KIT_TC334_LK ", I found that when I used the default parameters, Flash can be erased normally, but when I changed the initial address of erase from 0xA00E0000 to 0x80080020, I found that the erase seemed to fail. when I changed the initial address of erase from 0xA00E0000 to 0x80080020, I found that the erase seemed to fail, I think it may be caused by the macro definition "#define RELOCATION_START_ADDR (0x70100000U) ", please tell me what this macro definition means, and how to solve the problem here, thank you!
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/AURIX/The-Infineon-example-quot-Flash-Programming-1-KIT-TC334-LK-quot-failed-to-erase/td-p/723792
Show LessDear.
What is the difference between configuring full measurement as 0, or 1 in Lib_Meas_Fast_Sample function?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/%E5%8E%8B%E5%8A%9B%E4%BC%A0%E6%84%9F%E5%99%A8/SP49-full-measurement%E9%85%8D%E7%BD%AE/td-p/723774
Show Less我现在有6路pwm波,A、B、E、F、G、H,这六路pwm需要同时调频移相,我的B、E需要基于A移向,F需要基于E移相,G和H需要基于E移相,但是GTM-TOM模块pwm同时输出并满足移相有两种情况,一种是都基于A去移相,一种是基于前一个通道去移相,一旦我使用第一种,我的F基于A移相就会超过50%,这将导致PWM出现一个周期的高电平的波形,如果使用第二种我又无法满足我的移相标准,请问是否可以混合使用这两种模式,怎么使用?
祝好!
Show LessHi all,
We are evaluating EVAL_TDA38740_3.3VOUT.
Please check the attached file for the measurement circuit, register settings, component changes, and measurement conditions.
We would like to prevent the output current from jumping up due to sudden changes in the output voltage.
Is it possible to smoothly ramp up to the setting voltage?
If not, can you calculate the value of the jump voltage?
Best regards,
MS
Hi guys,
So I've done to set the serial number in fx3 as this KBA
But I have a question, so we are integrating the FX3 in our custom board which each serial number its about 12 characters,
and I tried to just write the Serial number as this:
const uint8_t CyFxUSBSerialNumberDscr[] __attribute__ ((aligned (32))) =
{
0x10, /* Descriptor size */
CY_U3P_USB_STRING_DESCR, /* Device descriptor type */
'M',0x00,
'Y',0x00,
'C',0x00,
'A',0x00,
'R',0x00,
'D',0x00,
'1',0x00,
'6',0x00,
'0',0x00,
'5',0x00,
'9',0x00,
'3',0x00,
};
But this will only show as:
How can I make it to look as the full serial number?
Thanks!
Show Less
<Question>
Does the Supervisory region (SFlash) area of CYT4BF support ECC?
If it support ECC,
Are the registers that control ECC common to FLASHC/FLASHC1_FLASH_CTL.MAIN_ECC_EN ?
(Please see T2G-B-H Architecture TRM,8.2.2.5 Code Flash ECC, Table 8-6. Flash ECC Enable Registers)
If it does not support ECC,
Please tell me why it is not support with ECC.or Is there any other monitoring function?
Thank you for your support.
<質問>
CYT4BFのSFlash領域はECCに対応していますでしょうか?
ECCに対応している場合、
8.2.2.5 Code Flash ECCに記載の、FLASHC/FLASHC1_FLASH_CTL.MAIN_ECC_ENのようなECCを制御するレジスタはありますでしょうか?
(T2G-B-H Architecture TRM, Table 8-6. Flash ECC Enable Registers参照)
・ECCに対応していない場合、
ECCに対応していない理由を教えてください。もしくはECC以外の監視機能はありますでしょうか?
よろしくお願い致します。
Show Less