Featured Discussions
Dear Supporter
I want to translate the following KBA. Please confirm to my work.
AURIX™ MCU: Possible combinations of error flags in SENT module – KBA239730
Regards,
Kazuki
Show LessDear Supporter
I want to translate the following KBA. Please confirm to my work.
Regards,
Kazuki
Show LessDear Supporter
I want to translate the following KBA. Please confirm to my work.
ModusToolbox™ "make" command hangs – KBA239829
Regards,
Kazuki
Show LessHi,
I have a AURIX MotorControl Application Kit with TC234LF, I want to switch from ADS to Visual Studio Code. I'm going to make it through the GCC compiler, but there is a problem using the winIDEA debugger. WinIDEA requires a license. I did not find a price list on the website and how to buy it.
Are there alternative debuggers that can be used in Visual Studio Code?
AN84868 is followed to implement using CX3 to configure FPGA. To be able use the FPGA configuration utility tool, descriptors are the same for AN84868 for FPGA configuration application firmware. After FPGA configuration, firmware switches to CX3 UVC application. FPGA configuration part is good, after switching to UVC application, video streaming is also good. Yet, UART is not able to send out debug information anymore in UVC application. UART debug works during FPGA configuration and printout information on data count for FPGA configuration process.
IO matrix configuration is the same for FPGA configuration application and for UVC application, i.e. I2C, SPI and UART peripherals are all enabled.
I am using GPIO 48 to 49 as the UART tx and rx.
What could be the problem?
Thank you for help in advance.
Show Less
As the title suggests, it's easy to implement in interrupt, but what should I write if I want to implement it in a general function? I didn't find any flag bits that I can use directly, but buffer has NDAT that I can determine directly.
The RF0N of the FIFO is under IR, I use this flag bit for judgment, and after 103 normal sends I get buserror.
How to realize this function?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/%E4%BE%8B%E7%A8%8B/CAN%E6%80%8E%E4%B9%88%E9%80%9A%E8%BF%87FIFO%E5%9C%A8%E6%94%B6%E5%88%B0%E6%8A%A5%E6%96%87%E5%90%8E%E5%86%8D%E6%8A%8A%E8%BF%99%E6%9D%A1%E6%8A%A5%E6%96%87%E5%8F%91%E9%80%81%E5%87%BA%E5%8E%BB/td-p/744593
Show LessHi,
I want to translate the following App Note to Japanese. Please confirm to my work.
"Getting started with 2ED2410-EM"
URL: https://www.infineon.com/dgdl/Infineon-2ED2410-EM-ApplicationNotes-v02_01-EN.pdf?fileId=8ac78c8c80f4d3290181235b7ca11c3a
Best Regards,
Hayashi.K
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/AURIX/%E7%94%B3%E8%AF%B7ADS%E7%BC%96%E8%AF%91%E5%99%A8/td-p/744522
Show LessHi.
Thank you for always providing assistance.
Android 14 update regarding the fixed MTU of 517 for BLE communication.
https://developer.android.com/about/versions/14/behavior-changes-all#mtu-set-to-517
We have conducted tests after applying the changes, but we've encountered an issue where data exceeding 512 bytes cannot be transmitted.
Since my customer job data often exceeds 512 bytes, we anticipate needing to split the data for transmission.
In the case of segmented transmission:
- Should a separate delay be applied for each packet during segmented transmission?
- Are there any specific considerations or performance optimization guides from the chipset manufacturer regarding segmented transmission?
- Is the current OTA issue(BTSDK-10583) related to the Request MTU as mentioned above?
- Can the OTA issue also be improved by using segmented transmission methods?
Thanks.
Regards,
DevRyan.
Show Less
What's the different between infineon's CAM sensor TLE4983, TLE4986, TLE4988, TLE4931?
Thanks
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/CAPSENSE-MagSense/Infineon-CAM-sensor-Type/td-p/744491
Show Less