Featured Discussions
Hi support,
I would like to set-up a UART connection on my NAC1080 using the GPIO0 and GPIO2 in order to communicate with my PC the messages that the NAC1080 will be sending.
I've been reviewing the uart_drv.h library you have available and what I can't see is how the data transmission works.
There's a function called "transmit_bytes()" that send the Tx buffer data, but where's the Tx buffer?
How could I edit the data on that buffer to be able to send the desired message?
Regards,
-K
Show Less
The current TC397_TFT v1.0 development board uses the TC397 A step of the chip, but I see ADS are TC397 B step routines, I will ADS in a few examples compiled and burned to the development version, can not run normally, respectively, through the TASKING and winIDE DEBUG found that the chip startup process will enter the Context Maneger Error Trap, the following figure belongs to, please ask! Please ask:
1. For Context Maneger Error Trap should be solved in what way?
1. Current ADS 1.9.20 supports TC397 A step chip, if not support and TC397A step corresponding to the example tutorial?
2. What is the difference between TC397 A step and TC397 B step?
TASKING DEBUG
winIDE
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/AURIX/TC397-TFT-v1-0%E5%BC%80%E5%8F%91%E6%9D%BF%E7%BC%96%E8%AF%91%E7%83%A7%E5%BD%95%E4%BB%BB%E6%84%8FADS%E7%A8%8B%E5%BA%8F%E4%BC%9A%E8%BF%9BContext-Maneger-Error-Trap/td-p/743094
Show LessHello, everybody:
I encountered the following problem, read the value in the register, check the register is "0x80000e23", but after reading, the first bit is not read, only read "0xe23", the type of the variable used to receive the value of the register is ( volatile uint32 )
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/TRAVEO-T2G/%E8%AF%BB%E5%8F%96%E5%AF%84%E5%AD%98%E6%9C%BA%E7%9A%84%E5%80%BC-%E7%AC%AC%E4%B8%80%E4%B8%AAbit%E8%AF%BB%E5%8F%96%E4%B8%8D%E5%88%B0/td-p/743090
Show Less
I tried to configure it using the above code, but it reports an error at device.set_acquisition_sequence(sequence).
Using the sample program found in the official distance_fft.py, using the
Perform the configuration. Is there any way to use config to configure it, or convert config to metrics and then configure it?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/%E9%9B%B7%E8%BE%BE%E4%BC%A0%E6%84%9F%E5%99%A8/BGT60TR13C-%E5%A6%82%E4%BD%95%E4%BD%BF%E7%94%A8%E5%8F%82%E6%95%B0%E9%85%8D%E7%BD%AE%E4%BC%A0%E6%84%9F%E5%99%A8%E8%8E%B7%E5%8F%96%E6%95%B0%E6%8D%AE/td-p/743081
Show Less大家好!
官方程序里的延时函数Delay_us(uint32 delay_time_us),在实际测试时,有个奇怪的现象。
测试程序看门狗设置1008ms,测试程序延时方式如下:
- Delay_us(500000); (void)WDT1_Service(); //延时500ms,喂狗
- Delay_us(600000); (void)WDT1_Service(); //延时600ms,喂狗
- Delay_us(1000000); (void)WDT1_Service(); //延时1000ms,喂狗
其中,1,3能正常工作,第2项延时600ms喂狗,程序没有喂狗成功,程序不工作。
Show LessThis Q&A just discussed P/D Flash, AURIX™ MCU: Error Correction Code (ECC) support - KBA238244
My question: is there special ECC for RAM and CAN relevant memory, e.g. Message RAM
Show LessHello,
I am trying to flash littlefs filesystem on thze qspi external serial flash memory in XMC7100 V1.1.
As I see library mtb-littlefs is not included in the XMC7100 kit.
- If I download any one of the PSoC6 kit and add the mtb-littlefs lirary to my project for XMC7100 v1.1 board build and run, Will it work?
- How do I mount the Littlefs to the external serial nor flash attached through qspi to the board ?
- I have limitation in using shread git repo therefore I have a local content storage added.
These are the errors when I try to add the PSoC6 library throught BSP Assistant:
Log file(s) for this session are stored at: C:\Users\Prasad\AppData\Local\Temp\Logs373088102786112282
Opening project creator from C:/Users/Prasad/ModusToolbox/tools_3.2/project-creator/project-creator.exe
Project Creator Status:
Project: littlefs
Location: C:/Users/Prasad/mtw/littlefsqspi/littlefs
Status: failed
Messages:
[1]: Could not fetch asset: 'recipe-make-cat1a' with ID: 'mtb://recipe-make-cat1a#mtb://recipe-make-cat1a', this asset does not exist in the manifest database. Check if your manifest XML files provide correct entry for the 'recipe-make-cat1a' asset
Could someone help me with another littlefs wrapper for the littlefs filesystem for XMC7100 kit?
best regard,
PrasadA
Show Less
Hi, I am new to radar sensors.
To analyze radar data, I have plotted FIFO data read from BGT60TR13C in time domain.
My concern is whether the data in the form below is read correctly.
Could you please tell me what the raw data in the time domain usually looks like and if it is correct?
Show Less
Hello
Can we allocate 2 nodes on MULTICAN_CONFIG_0, and operate all message objects of both the nodes using only one CAN_Rx and CAN_Tx through transceiver??
Hello,
I'm using WICED STUDIO 6.6. and CYW943907AEVAL1F.
I write a code that create some threads and these threads call malloc (and obviously subsequent free).
My problem is that after time during execution (this time is random) malloc returns me NULL
and the processor resets.
I checked so many times if malloc is followed by properly by a free and I found a correctly use.
I have the dubt that malloc is not thread safe: I mean that if I call a malloc in a thread and another thread is executing a malloc this can lead a crash.
Can someone help me ?
Show Less