Welcome to the Infineon Developer Community

Hi,

I want to translate the following KBA. Please confirm to my work.

https://community.infineon.com/t5/Knowledge-Base-Articles/Solid-state-relay-Frequently-asked-questions/ta-p/681026

Thanks,
MS

Hi,

I want to translate the following KBA. Please confirm to my work.

https://community.infineon.com/t5/Knowledge-Base-Articles/EiceDRIVER-Bipolar-vs-MOSFET-based-driver-current-booster/ta-p/681315

Thanks,
MS

Hi,

I want to translate the following KBA. Please confirm to my work.

https://community.infineon.com/t5/Knowledge-Base-Articles/Electronics-101-Topology-Fundamentals-and-Their-Basis-Waveforms/ta-p/412453

Thanks,
MS

Hi,

I want to translate the following KBA. Please confirm to my work.

https://community.infineon.com/t5/Knowledge-Base-Articles/Calculate-IGBT-losses-for-a-SPWM-voltage-source-converter/ta-p/381757

Thanks,
MS

Hi,

I want to translate the following KBA. Please confirm to my work.

https://community.infineon.com/t5/Knowledge-Base-Articles/CoolSET-Junction-to-Ambient-Thermal-Resistance-RthJA-and-Junction-to-Top-center/ta-p/404785

Thanks,
MS

I have fast data >200Mbps to be sent out to a Wifi access point.

The protocol of this fast data is SLVS.  So I would use an FPGA to convert from SLVS to USB2.0.

This FPGA shall then be interfaced to the CYW54907 USB2.0 port and transmitted over Wifi.

1) Do you see any issue with this setup configuration to the USB2.0 port of the CYW54907?

2) What is the typical throughput speed will I expect going from USB2.0 to Wifi over the air (assume the environment is clean from other radio sources)?    Will I be able to reach >200Mbps over the air with the CYW54907?

Trying to get the Phoenix RLC tester project up and running.

Cannot find the component project file.

Regards, Dana.

Eclipse IDE for ModusToolbox Version: 2.2.0 Build ID: 2181 CY8CPROTO-062-4343W KitProg3

I've been developing code using FreeRTOS for several months now, and suddenly the debug environment shuts down after programming my application.  No error mesages. I've tried undoing my changes, and the problem still occurs.  

srst_only separate srst_gates_jtag srst_open_drain connect_deassert_srst
Info : SWD DPIDR 0x6ba02477
shutdown command invoked
Info : psoc6.dap: powering down debug domain..

Program runs without pausing at start of main().  Runs as expected. I just can't debug it (no breakpoints, etc).

Problem doesn't occur with Hello World app.

Full capture:

Christian

I designed a PCB that uses the CYPD3177 for both negotiating 9V at 2A minumum and convert the voltage down to 5V via a buck converter, but which also uses the SAFE_PWR_EN as described in your schematic / documentation using two P channel mosfets to connect VBUS with 5V OUT in the case that the USB PD negotiations fail - in which case the 5V could still power my system in a low power mode.
However: for some reason the SAFE_PWR_EN pin is high (5V), when the system is connected to a regular USB power source (tested both with a USB A power adapter and a MacBook Pro via its USB-C port). But this means the mosfet stays disconnected and 5V OUT is not powered - which is the exact opposite behavior then what I expected. Expected was the SAFE_PWR_EN being pulled low, which then makes the P channel mosfets connect VBUS to 5V OUT.
Why is SAFE_PWR_EN high (5V) when a 5V source is connected and not low?
How do I fix this and make sure VBUS is connected to 5V OUT, when the USB PD negotiations fail?