Featured Discussions
Hi Everyone,
Today we are manufacturing sensors using the assembly KMI15/1 manufactured by NXP. We need an alternative because KMI15/1 is obsolete. We are looking at the Infineon #TLE4941PLUSC. The data sheet mentions that it needs a magnet on the back side - that solution is very similar to the KMI15/1. This is a link to the NXP assembly KMI15/1
KMI15/1 Integrated rotational speed sensor (nxp.com)
Can you provide the sensor TLE4941PLUSC (or similar) with that magnet attached to it?
Thank you, it would be great to see your answer.
Show Less
I can program the psoc5 using openocd now, with some caveats. However, if an NVL entry exists, it stops.
I have a project which somehow did something to the NVL.
I understand setting the Reset condition on the Pins can cause this. However, setting the pins to Don't Care doesn't fix this problem, so I suspect something else is causing the NVL to change.
Is there *any* gui / command line interface to find out what is causing the NVL to be set? (so it can be "fixed" in the project?)
This would not normally be a problem, but using openocd to program the psoc halts when the NVL entry is in the Creator generated hex file. I have multiple reasons for using openocd, some of which involve production machines. Others are very fast compile/debug cycle. (https://socmaker.com/?p=1004, and https://socmaker.com/?p=1027)
If I use objcopy, could I exclude that from the elf file for the new obj? (before making a hex file) If so, would it be by address? If so, which address? otherwise, how would I do that exclusion?
Is there a way to use openocd to program the NVL (perhaps kitprog in kitprog mode?) (Just checking)
Thanks!
Show Less
I am working on a wireless charger for electric vehicles and need MOSFET modules for generating the high-frequency AC. The FF3MR20KM1H might fit our application, but I didn't see the forward bias safe operating area plot.
We'd need to handle about 560A with a pulse width of 10.6uS.
Can this module handle this?
Show Less
I am attempting to follow the "Secure Boot" SDK user guide but continually run into the same problem. When attempting to setup the "CySecureTools" workspace i get the same error 'bash: cysecuretools: command not found' i get this even though i installed it and when i attempt to reinstall cysecuretools i got the message stating command already satisfied. This is all done on Windows
Show LessI am implementing a UVC MJPEG application using the FX3 which is sent MJPEG video frame data from an FPGA and we are seeing the following frame corruption. We are currently unsure where to start looking so any help on identifying what might be wrong would be helpful. This is 1080p30 streaming. The video does stream properly for a short while but if there is any moving content on the screen it tends to get corrupted. I have also included a photo of the proper streaming.
Show Less
I plan to port my design from CY7C68013A to CYUSB2014.
Can I use the same development tool and just select the different component?
Are there any potential issues I should be aware of?
Greg
Show Lessi'm trying SPI_CPU_1_KIT_TC334_LK.. I've joined SPI_A to SPI_B (confirmed on schematic for dev kit - - i hope).
when the code runs i dont have an LED on which says the data has transfered ok -- 😞 .. sad face .
i've run it a few times and set a break point . plus used a logic analyser ..
if i disconnect the MISO / MOSI lines i receive no data .. so i know the SPI slave is getting data.. ..
i've added this line , but nothing has changed ..
spiSlaveConfig.base.mode = SpiIf_Mode_slave; /* Configure the mode */
into the init config for the slave module..
i will continue to look but if anyone has seen this before.....
Where are CAD models for QDPack.
There are .pdf files at https://www.infineon.com/cms/en/product/packages/PG-HDSOP/PG-HDSOP-22-1/ These are NOT CAD models.
STEP form would be preferred.
Greg
Show LessMy radar is Distance2GoL.
I reconfigure the firmware in config.h, make the one frame is 40ms, each frame has 10 pulses, and each pulse lasts 2ms.
First when I charge the board and use OSC to watch it's TX_EN, everything is finr just like I set. Here is the picture of the TX_EN:
But, when I start use matlab to acquire the raw data, when I run the matlab code, it has been changed.
Here is the TX_EN when I start to rum the matlab code:
Please tell me why this matlab code just for acquire the raw data will affect the radar, what should I do to modify the matlab code?
Show LessI am looking for a Power MOSFET. I need a Silicon (Si) transistor with high Vds >500V, but I don't know how to find the transistor I need. The list on the website doesn't state transistor material. Please help.
Show Less