Welcome to the Infineon Developer Community

The microcontroller is running, but One eye does not have an operating interface.

Show Less

Reason for application: Puhua basic software to participate in the TC4 Hypervisor training, harvested a lot, the training teacher is also now demonstrating the DEMO project, and said that based on the ADS compiler can be downloaded this DEMO, just this ADS compiler is still their internal version of Infineon, you need to get if you want to get to them to apply for Infineon, they will be reviewed and approved by the release of the download link to the After their approval, they will release the download link to our registered Infineon account. Please help us to communicate with Infineon to see if they can release the ADS compiler software for Hypervisor's TC4D9 project to us. After we have the ADS compiler and the DEMO project, we or the R&D center can train our internal colleagues based on the TC4 development board, based on some features of the TC4 Hypervisor.

smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/AURIX/%E7%94%B3%E8%AF%B7ADS%E7%BC%96%E8%AF%91%E5%99%A8/td-p/744522

Show Less

Hi.

Thank you for always providing assistance.

 

Android 14 update regarding the fixed MTU of 517 for BLE communication.

https://developer.android.com/about/versions/14/behavior-changes-all#mtu-set-to-517

We have conducted tests after applying the changes, but we've encountered an issue where data exceeding 512 bytes cannot be transmitted.

Since my customer job data often exceeds 512 bytes, we anticipate needing to split the data for transmission.

In the case of segmented transmission:

• Should a separate delay be applied for each packet during segmented transmission?
• Are there any specific considerations or performance optimization guides from the chipset manufacturer regarding segmented transmission?
• Is the current OTA issue(BTSDK-10583) related to the Request MTU as mentioned above?
• Can the OTA issue also be improved by using segmented transmission methods?

 

 

 

Thanks.

Regards,

DevRyan.

 

Show Less

What's the different between infineon's CAM sensor TLE4983, TLE4986, TLE4988, TLE4931?

Thanks

smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/CAPSENSE-MagSense/Infineon-CAM-sensor-Type/td-p/744491

Show Less

This is in regards to 1ED3124MC12H trying to drive IGBT model FZ900R12KP4HOSA1.

All my questions below are in regards to the gate driver.

1. For the IN+ and IN-, I assume that I would need to use a PWM signal to turn on the IGBT? If so, what are the voltage and also the duty cycle percentage parameters for the PWM signal to turn on the IGBT?

2a. IN+ is a non-inverted control signal, and IN- is an inverted control signal. Does this mean IN+ turns ON the IGBT and IN- turns OFF the IGBT?
2b. If yes, does this mean I must send an inverted PWM signal in order to turn off the IGBT after I turned it on?

3. Does IN+ connect to the positive (+) of the PWM module and IN- connect to the negative (-) of the PWM module?

4. Based upon page 8, Figure 6, correct me if I'm wrong but it seems we need 3 voltage supplies?
a. A +3.3V from VCC1 to GND1 (with a 100nF capacitor in-between)
b. A +15V from VCC2 to an independent branch (with a 4 microfarad capacitor in-between)
c. A -8V from the independent branch to VEE2 (with a 4 microfarad capacitor in-between)

5. Is SGND simply the ground for VCC1, separated by a 100nF capacitor? The reason I'm asking is because I've never seen the term "SGND". I'm not sure what the "S" means in "SGND".

Show Less

I need a usb C power delivery (upto 100W) adapter/power bank design files using this chip CYPD7271-68 QXQ to understand the hardware of this chip. can somebody kindly provide that?

Show Less

 

Hi,

 

I am using the following eval board and not using RTOS in my project. I am trying to setup an interrupt based systick timer and looking for some information on how to do so since I haven't setup any interrupts yet.

https://www.infineon.com/cms/en/product/evaluation-boards/eval_pmg1_b1_drp/

 

Show Less

As has been reported elsewhere, I am getting "The given PDL path "C:\Program Files (x86)\Cypress\PDL\3.1.7" is invalid. Unable to find required PDSC file." when I attempt to Generate Application.  I am trying to run the "Hello World" application, i.e. just getting started with PSoC 6.  The path should be valid since I found it via the "Browse" button.  

Can someone advise me how to fix this?
Thank you.  

 

 

 

 

Show Less

Can you please tell me why it is so disassembled here? Is there any basis for this? #RC Absorption #Snubber #Buffer Circuits

 

smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/MOSFET-Si-SiC/%E5%85%B3%E4%BA%8E-%E7%BC%93%E5%86%B2%E7%94%B5%E8%B7%AF%E5%A6%82%E4%BD%95%E4%B8%BA%E5%BC%80%E5%85%B3%E7%94%B5%E6%BA%90%E4%BF%9D%E9%A9%BE%E6%8A%A4%E8%88%AA-%E5%8F%88%E8%AF%A5%E6%80%8E%E4%B9%88%E8%AE%BE%E8%AE%A1%E5%91%A2-%E8%8B%B1%E5%AE%B6%E5%BF%85%E4%BF%AE%E8%AF%BE-%E4%B8%AD%E5%B0%86%E4%B8%89%E9%98%B6%E7%94%B5%E8%B7%AF%E6%8B%86%E5%88%86%E4%B8%BA%E4%B8%A4%E4%B8%AA%E4%B8%A4%E9%98%B6%E7%94%B5%E8%B7%AF/td-p/744424

Show Less

Hello,

Recently if I open PSoC Designer normally (not as admin) I can open projects but the top file menu ribbon is not available and I can't do any build or debugging.

If I run Designer as admin then the project does not open and I get this error:

has anyone had this problem? Any help is appreciated.

 

Show Less