Welcome to the Infineon Developer Community

TLE5012B The E1000 reads and writes the MODE3 register, and after I write the angle value in, occasionally the value read out is 0X8091, not the value I wrote in.

smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/%E8%A7%92%E5%BA%A6-%E7%A3%81%E6%80%A7%E4%BC%A0%E6%84%9F%E5%99%A8/TLE5012B-E1000%E8%AF%BB%E5%86%99%E5%AF%84%E5%AD%98%E5%99%A8/td-p/740382

Hi, Infineon team,

I want to know how to design for CSX Touchpad.
It seems that there is the document of AN234185 PSoC™ 4 CAPSENSE™ Touchpad design guide .
But I can't reach this link: https://www.infineon.com/002-34185

The PCB reference data has been gotten from the link in this thread.
https://community.infineon.com/t5/ModusToolbox/PSOC-capsense-touchpad-handwriting/m-p/381127#M497

However, I would like to know the design rules, and why these designs should be used.
If possible, could you provide me the AN234185?

Best Regards,

Hello,

IRFP044NPBF is discontinued, I found IRFP064NPBF, can I use it to replace the IRFP044NPBF ?

My project uses this mosfet as an electronic load for 20V, 3A, 60W max.

Actually it is the count parameter in this API for creating DMA channels, which is interpreted as the number of buffer zones to be allocated for the channel, can it be understood that which channel is configured, this parameter will allocate buffer zones for that channel? I can understand that which channel is configured, this parameter will allocate cache area for that channel?

smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/%E4%BD%8E%E9%80%9F-%E5%85%A8%E9%80%9F-%E9%AB%98%E9%80%9F-USB-%E5%A4%96%E8%AE%BE/%E5%86%85%E9%83%A8API%E5%8F%82%E6%95%B0%E7%96%91%E6%83%91/td-p/740308

I configured the freeRTOS environment through BSP Assistant and Lib Manager, MY MCU is PSOC62, with m0 and m4 kernel, but after configuring it, both m0 and m4 project directories will bring the freeRTOS file, but I only want to use the freeRTOS in the M4 directory.

Kindly provide the MTBF and FIT data for 

Kindly provide the MTBF and FIT data for the following components.

Hi,

I want to translate the following article to Japanese. Please confirm to my work.
KBA "The bootstrap capacitor on the high side of a gate driver provides the energy required to turn on a high-side power switch."
URL: https://community.infineon.com/t5/Knowledge-Base-Articles/The-bootstrap-capacitor-on-the-high-side-of-a-gate-driver-provides-the-energy/ta-p/739554

Best Regards,
Hayashi.K

Before installing HighTech, I could connect to the development board normally using Memtool+MiniWigger debugger, but after installing Hightech, I found that the debugger could not be connected, and the device could not be recognized normally in "Device Manager >Universal Serial Bus Controller ".

smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/AURIX/%E5%AE%89%E8%A3%85HighTech%E8%BD%AF%E4%BB%B6%E5%90%8E-%E5%AF%BC%E8%87%B4%E8%AF%86%E5%88%AB%E4%B8%8D%E5%88%B0MiniWigger%E8%B0%83%E8%AF%95%E5%99%A8/td-p/740200