Welcome to the Infineon Developer Community

近日，我购买了一块KIT_AURIX_TC397_TFT板子，里面是官方默认的固件， 我看说明书里通过板子的Mini USB连接PC,  就可以识别到板子，但是我用usb连接后，板子TFT屏幕正常点亮，只有D106 (V_UC)、D104 （SS2）灯亮和P13中的一颗灯在闪烁，但在PC设备管理器里面找不到Infineon JDS DAS COM和Infineon JDS DAS Debug，安装DAS软件也无法识别，这种情况应该怎么处理?

Hello,

I would like to design a synchronous buck converter using XMC4200. I would like to implement a soft-start. How can I do that? Is there any documentation to help?

Thanks.

Jedison

Hi,

I have some question regarding the BGT60LTR11AIP (+Shield + MCU7 radar baseboard):

When using Radar Fusion GUI_1.5.4 to detect sensor BGR60LTR11AIP, the LEDs on the sensor and development board can light up normally and change colors when objects are moving. However, the device cannot be found in the software Radar Fusion GUI_1.5.4. I want to manually update the firmware, but there is no response from the device or firmware version drop-down box in the Decision ->Flash Firmware dialog box. I have reviewed the solutions on the forum regarding BGR60LTR11AIP No Decided, but I have not found where to download the "Radar BGT60LTR11AIP" software and the file "InitializeBGTxxx. bat", and where should I download this file.

Radar Fusion Gui Version: v3.5.4

Thanks for your time,

Regards,

xiao

Hi all,

We would like to measure the phase margin at EVAL_TDA38740_3.3VOUT.

Could you please check if the attached method is correct?

If it is not correct, please tell me how to measure it.

If you have the phase margin of EVAL_TDA38740_3.3VOUT, please provide it for us.

Best regards,
MS

Hi

I want to us HID at cyw20706.

https://community.infineon.com/t5/ModusToolbox/I-can-t-find-HID-example-in-ModusTool-box/m-p/399265#M2521

Based on the above question, an example exists for cyw20835.

I wonder if this example can be applied to cyw20706.

I was told at the time that it was not possible, is it the same now?


Thank you.

Regards,

DevRyan.

DPLL的RAM2C区域用来保存TRIGGER信号的特征，相应的内存寄存器为Memory DPLL_ADT_T[x],但是直接使用这个寄存器在ADS中无法识别此寄存器，求助。

Hydrogen production power supply front-end topology, how do IGBTs work in the DC/DC section, and why use two of them?

smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/IGBT/%E4%B8%8B%E9%9D%A2%E6%8B%93%E6%89%91%E7%BB%93%E6%9E%84%E6%98%AF%E4%BB%80%E4%B9%88%E5%8E%9F%E7%90%86/td-p/739767

Hello

I'm using a le_hello client app, and I'm curious about the consistency of advertising intervals.
Currently, the scan settings are high_duty_scan_interval 320, high_duty_scan_window 160, and high_duty_scan_duration 0.
The advertising settings are low_duty_min_interval 2048, low_duty_max_interval 2048, and low_duty_duration 0.
The mode in use is BTM_BLE_ADVERT_UNDIRECTED_LOW for advertising and BTM_BLE_SCAN_TYPE_HIGH_DUTY for scanning.

When I measured the scan list with NRF Scanner, most items are displayed at 1.28-second intervals, but there are cases where the advertising interval becomes 8 seconds. I'm curious if the advertising is consistently displayed at 1.28-second intervals, and if not, if it's related to scanning. Also, how can I check the advertising interval?
If you have any related documents or code examples, I would appreciate it if you could share them.

Hello, World!

I am trying to install ModusToolbox and am getting the error message 

Error: Failed to Login: "Network Error occurred": 'ContentNotFoundError'

Steps to reproduce:  

1) Download and install the developer center launcher

2) Launch ModuxToolbox Setup

At this point the software gives the error message

At this point, it doesn't matter if I click "Login" or click on "ModusToolbox Tools Package". Login doesn't even ask me for a username. I get the same error message and "Next >" never becomes enabled.  

Any help would be appreciated.

I was looking for a reliable power bank module with USB C fast charge support. After searching I got VD_USB_CCG3PA_45W_PWRBNK. But the problem with this module is that:

1. I want one more USB TYPE A port.

2. one micro USB port for charging 

3. The module should be run by a standard LIPO battery whose voltage can vary between 3.7-4.2 volts.

Now my question is, is there any other solution board which has these three features? if no, then is it possible to modify the original hardware and add these 3 features? can somebody tell me what modification should be done in the schematic so that I can avail these features?