Welcome to the Infineon Developer Community

Hi,
https://community.infineon.com/t5/OPTIGA-TPM/Configuring-SLB9673-for-the-purpose-of-secure-boot/m-p/614349 
we tried implementing the IMA as suggested in the above post
we were able to measure all the files when we set the following at the kernel command line
ima=on lsm=integrity ima_appraise=fix ima_policy=tcb ima_template=ima-sig

We noticed that the policy file at /sys/kernel/security/ima/policy was a default policy, we would like to know how to create a custom policy and load the same for measuring a particular file and appraising the same file

Thanks 
Mythreyi

Dear Supporter

I want to translate the following KBA. Please confirm to my work.

TRAVEO™ T2G MCU: Protection context (PC) requirements for system calls – KBA239469

Regards,

Kazuki

Dear Supporter

I want to translate the following KBA. Please confirm to my work.

TRAVEO™ T2G MCU: Analyzing T2G devices in DEAD state – KBA239492

Regards,

Kazuki

Dear Supporter

I want to translate the following KBA. Please confirm to my work.

AURIX™ MCU: GETH embedded MTL queue FIFOs handling - KBA239698

Regards,

Kazuki

Dear Supporter

I want to translate the following KBA. Please confirm to my work.

AURIX™ MCU: Possible combinations of error flags in SENT module – KBA239730

Regards,

Kazuki

Dear Supporter

I want to translate the following KBA. Please confirm to my work.

EZ-PD™ PMG1-B1 MCU: Firmware modification on EVAL_PMG1_B1_DRP kit to charge 2-cell to 5-cell lithium-ion battery – KBA239827

Regards,

Kazuki

Dear Supporter

I want to translate the following KBA. Please confirm to my work.

ModusToolbox™ "make" command hangs – KBA239829

Regards,

Kazuki

Hi,

I have a AURIX MotorControl Application Kit with TC234LF, I want to switch from ADS to Visual Studio Code. I'm going to make it through the GCC compiler, but there is a problem using the winIDEA debugger. WinIDEA requires a license. I did not find a price list on the website and how to buy it. 

Are there alternative debuggers that can be used in Visual Studio Code?

AN84868 is followed to implement using CX3 to configure FPGA. To be able use the FPGA configuration utility tool, descriptors are the same for AN84868 for FPGA configuration application firmware. After FPGA configuration, firmware switches to CX3 UVC application.  FPGA configuration  part is good, after switching to UVC application, video streaming is also good. Yet, UART is not able to send out debug information anymore in UVC application.  UART debug works during FPGA configuration and printout information on data count for FPGA configuration process.

IO matrix configuration is the same for FPGA configuration application and for UVC application, i.e.  I2C, SPI and UART peripherals  are all enabled. 

I am using GPIO 48 to 49 as the UART tx and rx. 

What could be the problem?

Thank you for help in advance. 

As the title suggests, it's easy to implement in interrupt, but what should I write if I want to implement it in a general function? I didn't find any flag bits that I can use directly, but buffer has NDAT that I can determine directly.

The RF0N of the FIFO is under IR, I use this flag bit for judgment, and after 103 normal sends I get buserror.

How to realize this function?

smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/%E4%BE%8B%E7%A8%8B/CAN%E6%80%8E%E4%B9%88%E9%80%9A%E8%BF%87FIFO%E5%9C%A8%E6%94%B6%E5%88%B0%E6%8A%A5%E6%96%87%E5%90%8E%E5%86%8D%E6%8A%8A%E8%BF%99%E6%9D%A1%E6%8A%A5%E6%96%87%E5%8F%91%E9%80%81%E5%87%BA%E5%8E%BB/td-p/744593