Welcome to the Infineon Developer Community

Dear Supporter

 

I want to translate the following KBA. Please confirm to my work.

Temperature dependency of MOSFET parasitic capacitances and losses

Temperature dependency of MOSFET parasitic capacit... - Infineon Developer Community

 

Regards,

AkUm

Show Less

after self-programming and reset, the software blocked at function _c_init_entry (judged by asm code) the trap position is where the global variable are being initialized by data stored in flash the flash area (32 bytes) have ecc errors why and how did these ecc errors occur? Show Less

Hi All, 

I am kind of new to Radar sensor technology.

I tried to go through the DS of the BGT60TR13CT radar sensor but couldn't really understand what sort of Data I would be receiving over the SPI protocol. My use case is, I want to interface the sensor with a 3rd party microcontroller, to read and process the raw data that I'll be receiving, so that I can classify target present and target not present states.

Could somebody please guide me regarding what sort of data frame I would be receiving and how to process the same, for my use case. 

Thanks and regards,

Sabyasachi.

#BGT60TR13CT

 

Show Less

Hi,

I want to translate the following article. Please confirm to my work.
URL: https://community.infineon.com/t5/Knowledge-Base-Articles/How-can-uIO-Stick-user-program-readout-into-from-data-flash-area/ta-p/683553

Best Regards

Show Less

Hi,

I want to translate the following article. Please confirm to my work.
URL: https://community.infineon.com/t5/Knowledge-Base-Articles/How-to-Renew-MOTIX-TLE987x-Motor-Control-F...

Best Regards

Show Less

 

we are trying to re flash the Micro Via MODUS tool .it is getting heat while flashing after 60% completed. and our tool shows power interrupt .

Error Image from our flashing tool:

please support to resolve this issue. we are struggling to Re flash the Micro . kindly share your input to resolve the issue.

Show Less

Hi,

I want to translate the following article. Please confirm to my work.
URL: https://community.infineon.com/t5/Knowledge-Base-Articles/How-to-Renew-MOTIX-TLE987x-Motor-Control-FOC-Demo-License/ta-p/682109

Best Regards

Show Less

Hi,

I want to translate the following article. Please confirm to my work.
URL: https://community.infineon.com/t5/Knowledge-Base-Articles/Can-a-single-ceramic-cap-be-used-for-VDDP-and-VDDC-outputs-in-TLE9844/ta-p/682100

Best Regards

Show Less

Hi,

Does this controller have a internal temperature sensor? I would like to clarify this because  the CCG3 Tecnical Reference manual says

The 8-bit ADC is used for generic voltage sensing of anything connected to the analog mux (AMUX buses, as well as voltage supply measurement and temperature sensing.

Also SDK has some references to ADC temperature sensing.

/*
 * ADC1 SAR Control Register
 * General Purpose voltgae measurement, Temperature Sceining
 */
#define PDSS_ADC1_SAR_CTRL_ADDRESS                          (0x400a01a0)
#define PDSS_ADC1_SAR_CTRL                                  (*(volatile uint32_t *)(0x400a01a0))
#define PDSS_ADC1_SAR_CTRL_DEFAULT                          (0x00008000)

Is there a internal sensor or are these just referring to a some external sensor like NTC thermistor connected to a pin and muxed to ADC?

Thanks!

Show Less

Hello,

I'm running MTB 3.2 GUI in Ubuntu 22.04.4 LTS and building the Security_App PSoC6 example for the Prototyping Kit (CY8CPROTO-062-4343W).

After creating the default Security_App example, I added the emeeprom (v2.20.0) component, so as to read/write settings to the PSoC6 32kB Auxilliary Flash.  I copied the code from Emeeprom's README.md

https://infineon.github.io/emeeprom/em_eeprom_api_reference_manual/html/index.html#section_em_eeprom_quick_start

And added a line CY_SECTION(".cy_em_eeprom") , so that emEepromStorage will be kept in the 32kB Auxilliary Flash.

However, the code failed to compile:

/opt/Tools/ModusToolbox/tools_3.2/cymcuelftool-1.0/bin/cymcuelftool --merge ../proj_cm0p/build/APP_CY8CPROTO-062-4343W/Debug/proj_cm0p.elf ./build/BOOT/APP_CY8CPROTO-062-4343W/Debug/proj_cm4.elf --output ./build/BOOT/APP_CY8CPROTO-062-4343W/Debug/primary_app.elf --hex ./build/BOOT/APP_CY8CPROTO-062-4343W/Debug/primary_app.hex; cp -f ./build/BOOT/APP_CY8CPROTO-062-4343W/Debug/primary_app.hex ./build/BOOT/APP_CY8CPROTO-062-4343W/Debug/primary_app_BOOT_raw.hex; rm -f ./build/BOOT/APP_CY8CPROTO-062-4343W/Debug/primary_app.hex; /opt/Tools/ModusToolbox/tools_3.2/gcc/bin/arm-none-eabi-objcopy --change-addresses=0 -O ihex ./build/BOOT/APP_CY8CPROTO-062-4343W/Debug/primary_app.elf ./build/BOOT/APP_CY8CPROTO-062-4343W/Debug/primary_app_BOOT_unsigned.hex; ../../mtb_shared/core-make/release-v3.3.1/make/scripts/python3.bash ../../mtb_shared/mcuboot/v1.8.1-cypress/scripts/imgtool.py sign --header-size 0x400 --pad-header --align 8 -v 1.0.0 -S 917504 -M 1792 --overwrite-only -R 0 -k ../proj_btldr_cm0p/keys/cypress-test-ec-p256.pem ./build/BOOT/APP_CY8CPROTO-062-4343W/Debug/primary_app_BOOT_unsigned.hex ./build/BOOT/APP_CY8CPROTO-062-4343W/Debug/primary_app.hex; cp -f ./build/BOOT/APP_CY8CPROTO-062-4343W/Debug/primary_app.hex ./build/BOOT/APP_CY8CPROTO-062-4343W/Debug/primary_app_BOOT.hex;
No ELF section .cychecksum found, creating one
Application checksum calculated and stored in ELF section .cychecksum
No ELF section .cymeta found, creating one
Checksum calculated and stored in ELF section .cymeta
Usage: imgtool.py sign [OPTIONS] INFILE OUTFILE
Try 'imgtool.py sign -h' for help.

Error: Image size (0x3fe0896) + trailer (0x20) exceeds requested size 0xe0000

make[1]: Leaving directory '/home/ub2204/work/psoc/tansiowk_mtw_3_1/Security_App_Emeeprom/proj_cm4'
cp: cannot stat './build/BOOT/APP_CY8CPROTO-062-4343W/Debug/primary_app.hex': No such file or directory
make[2]: *** [../../mtb_shared/core-make/release-v3.3.1/make/core/bwc.mk:161: _mtb_build__legacy_project_postbuild] Error 1
make[1]: *** [../../mtb_shared/core-make/release-v3.3.1/make/core/main.mk:385: secondstage_build] Error 2
make: *** [/opt/Tools/ModusToolbox/tools_3.2/make/application.mk:72: build] Error 2
"/opt/Tools/ModusToolbox/tools_3.2/modus-shell/bin/make CY_MAKE_IDE=eclipse CY_IDE_TOOLS_DIR=/opt/Tools/ModusToolbox/tools_3.2 CY_IDE_BT_TOOLS_DIR= -j6 all" terminated with exit code 2. Build might be incomplete.

I have attached the code, build error log and map file.

Thanks for any advice!

BR,

SK

Show Less