Featured Discussions
Hello all,
I am able to see UCB_PLFASH register on my TC38x.
But UCB_DFLASH I am unable to see. Initially I was able to see and modify also with Trace32.
Can anyone suggest what to do?
PFA image for reference w.r.t current situation.
Thanks in advanced.
Show Less
When i porting stm32h745 + Laird(lwb+), but stoped install firmware.
I think bluetooth sensor can't init hello_sensor_application_init();
But nucleo-745zi-q + Lwb(4343w) it's worked.
Show Less
I would like to ask what would cause this error?
What I have in my code is to create an array of outputs on the INT side of EP0 in the UART callback function, and then push the data from inside the UART out through the IN side of EP0. Now this build output array reports an error
Serial DEbug Reply:
What's going on here? Anyone know?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/USB%E4%B8%BB%E6%9C%BA%E9%9B%86%E7%BA%BF%E5%99%A8%E6%94%B6%E5%8F%91%E5%99%A8/USB%E8%BD%AF%E4%BB%B6%E9%85%8D%E7%BD%AE%E9%97%AE%E9%A2%98/td-p/724545
Show LessHello.
Regarding 3DL After entering deepsleep, the MCU current is around 4mA when measured separately. Both cores executed Cy_SysPm_DeepSleep to confirm that the MCU entered DeepSleep. what could the high current be related to?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/TRAVEO-T2G/3DL-deepsleep-%E7%94%B5%E6%B5%81/td-p/724510
Show LessHello, I've recently been learning how to extract respiratory heart rate signals with BGT60TR13C radar with Python. How can I convert the recorded data to the data required for FFT?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/%E9%9B%B7%E8%BE%BE%E4%BC%A0%E6%84%9F%E5%99%A8/How-to-use-BGT60TR3C-to-extract-respiratory-heart-rate-signals-in-Python/td-p/724498
Show LessI am new to the PowIR Build tool, I need to understand how to set the output voltage for IRPS5401, I have done required configuration based on my requirement when I create a new device and I have all input voltages, output voltages, etc. for SWA, SWB, SWC, SWD, LDO I have created a pcd file, but I want desired output to be written into the register not into the OTP .
Before writing/testing with config file I want to understand the tool, with default values when i2c is detected how to write value into the register and read.
If someone could point me the procedure of writing into the register it would be helpful for me to understand the tool by providing any source code or detailed pdf (Guide)
Thanks & Regards
Muvva Navin Krishna
Show LessHi
I am trying to create a simple program to read 10 bytes on UART through DMA and then write it again to the UART using DMA.
I added blinking LEDs in the DMATxISR and DMARxISR as visual indication that the ISR is being called.
It works for DMA Rx, but fails in DMA Tx.
I tried to use memcpy() to copy the Rx buffer into the Tx buffer to engage DMATx, but it doesn't work. I can only send using PutArray().
I attached my project,
I wonder if you can help me out find the mistake.
thanks
Show LessHi Sir
We are using Nvidia Jetson Nano + CYW55573/AWXB327MA-PUR M.2 , referring to the Nvidia Jetson bring-up with Infineon AIROC Wi-Fi 6 CYW5557x documentation at https://github.com/neilch0811/Infineon-AIROC-Wi-Fi-Nvidia-Release/blob/5099250b501d4e06dbd8c7e96d163decb8a82d75/Nvidia%20Jetson%20Orin%20AGX%2BCYW55573-DebianPkg-BringupSteps.pdf
and
https://github.com/neilch0811/Infineon-AIROC-Wi-Fi-Nvidia-Release/blob/main/AIROC%E2%84%A2%20CYW5557x%20Wi-Fi%206%20%26%20Bluetooth%C2%AE%20bring%20up%20with%20Nvidia.pdf. We can successfully connect to the internet using command-line instructions. However, we are unable to manage Wi-Fi using the OS's built-in network manager. The options related to Wi-Fi in the network manager are greyed out, and wpa_supplicant is mentioned to be used from FMAC. Can you provide us with some guidance on how to address this issue? Thank you.