Welcome to the Infineon Developer Community

HI

I would like to build a trigger control for a youtube maker project , using the TLE493D-W2B6

I have an TLE493DW2B6 shield2go board, and I connected it to the Arduino 

I installed the library TLE493D

I copied the DrillTrigger_SpeedAsNumber example

https://github.com/Infineon/TLE493D-3DMagnetic-Sensor/tree/master/examples/DrillTrigger_SpeedAsNumber

connected the sensor to the ARduino UNO R3   I2C pins (checked with the oscilloscope I can see SCL adn SDA moving correctly)

Connected the VDD pin of the board to 3V3 and the GND to GND

but all I can read are always the same number (see screenhsot below)

even if I put a magnet on the top of the sensor:

am I missing something?

thanks

Fabio

Hi,

I am using CY8C6245LQI-S3D42 and I used the DFU examples to boot the system and created the application to run on AM4 core and everything is working well. 

I wait for 5 sec in DFU to check if there is any updates or just move with the Application code.

I find that sometimes the device stops booting once in a blue moon. Now If I flash again just the boot loader, everything is fine , I need not have to write the Application, it moves from DFU in 5 sec to application.

I believe, there is some how the flash/DFU is getting corrupted.  I want to protect this scenario. Can some one share how do I protect my DFU so that it never erases . Any example's will be appreciable, I am using USB CDC transport in DFU.

Regards,

Madhav

I'm exploring the CSX Touchpad Tuning sample application using the PSoC4 MAX Pioneer kit. In the user manual for the CAPSENSE Tuner app, it says "The middleware supports simultaneous detection up to three touches for a CSX touchpad
touch, so the touch table displays all the detected touches." However, I can only get two touches to show in the CSX Touch Table on the Touchpad View in the Tuner app. I can see the third (and when appropriate, fourth) finger in the main Widget View graphic, but notice only two of the fingers have a colored "dot" in the middle representing the centroid of the touch. I suspect I need to modify the number of centroids that are being tracked and/or reported, but am not sure what parameter I need to change in the capsense_defines header file to do this.  

Also, what is the nature of the limitation of the middleware only supporting three simultaneous touches? Is there a theoretical limit of touches CAPSENSE can support? 

Hello,

I'm working on a project for a company where I need to implement Ethernet with UDP using Lwip. I noticed that there is no example on this particular subject. I only found examples of TCP echo. Nevertheless, I am attempting to write my own code for implementing a UDP server (code shown below). Then, I implement the function(udpServer_Init) in the main_cpu0 program. When I try to run the program, I can ping the microcontroller, but when I attempt to connect via Putty terminal, it says "connection refused." I am wondering if I am missing some settings in lwipopts.h or if I am overlooking something else. I would greatly appreciate it if anybody could provide me with some examples of UDP on the Aurix microcontroller or provide any help regarding this problem. I am also including important program files in the attachment.

Howdy y'all,

As the title implies, I was curious as to what the recommended torque was to secure the IPTC012N08NM5 to a heatsink? I couldn't find anything in the datasheet or any of the supplemental documentation on what the force should be. 

Thanks 

We are using Tasking IDE on Aurix evaluation board. There’s a build in miniWiggler debugger. We can use this miniWiggler debugger to debug the code. We can set break points, stop at break points, evaluate variables at break points. However, one main feature is not working in all the PCs: we cannot do “step into”, “single step”, “step through” features. We must unset the break point in the current step and set a break point in the next step then hit “continue to run” to mimic the “single step” feature. Is that the problem with the debugger? Do j-link debugger work with Tasking IDE?

Thank you so much for your answer.

Hi,

Looking at the latest ModusToolBox 3.2 I couldn't find an Ethercat Example for the board KIT_XMC48_RLX_ECAT_V2.1, is there any plan to port the Dave example to MTB as well?

Best Regards,

Marcelo Macedo - FAE at Neutronics