IGBT Forum Discussions
This is in regards to 1ED3124MC12H (https://www.infineon.com/cms/de/product/power/gate-driver-ics/1ed3124mc12h/) trying to drive IGBT model FZ900R12KP4HOSA1 (https://www.infineon.com/cms/en/product/power/igbt/igbt-modules/fz900r12kp4/).
I have a few questions specifically about the gate driver:
1. For the IN+ and IN-, I assume that I would need to use a PWM signal to turn on the IGBT? If so, what are the voltage and also the duty cycle percentage parameters for the PWM signal to turn on the IGBT?
2a. IN+ is a non-inverted control signal, and IN- is an inverted control signal. Does this mean IN+ turns ON the IGBT and IN- turns OFF the IGBT?
2b. If yes, does this mean I must send an inverted PWM signal in order to turn off the IGBT after I turned it on?
3. Does IN+ connect to the positive (+) of the PWM module and IN- connect to the negative (-) of the PWM module?
4. Based upon page 8, Figure 6, correct me if I'm wrong but it seems we need 3 voltage supplies?
a. A +3.3V from VCC1 to GND1 (with a 100nF capacitor in-between)
b. A +15V from VCC2 to an independent branch (with a 4 microfarad capacitor in-between)
c. A -8V from the independent branch to VEE2 (with a 4 microfarad capacitor in-between)
5. Is SGND simply the ground for VCC1, separated by a 100nF capacitor? The reason I'm asking is because I've never seen the term "SGND". I'm not sure what the "S" means in "SGND".
Thank You
Show Less您好, (1)目前的驱动芯片:1ED020I12-F2(2A),IGBT模块:FS3L50R07W2H3F_B11(650v,50A)工作环境是直流母线电压在300V,纯阻性负载功率1000w。 (2)但是在300V工作20s后,IGBT烧坏了。损坏情况如图,一共四处。这是因为什么?过压(电压选型的裕度应该够吧),过流?为什么会出现这种情况?会有哪些原因导致? (3)能推荐一下同样的封装的驱动芯片和IGBT吗?或者推荐一个过流值比较大的驱动芯片? 期待您的解答
Show LessWe're working on several induction systems for integrated use in tanks.
Planning to base the 230V 16A 1-phase designs on the evaluation kits provided, but we also need a 400V 16A 11kW system for use with 1-2 coils (2-4 IGBTs)
Can you please assist in the general components recommended for the EMI filter, bridge rectifier circuits and IGBTs for such a setup?
Should we use one 400V 3-phase bridge per IGBT pair or share it?
Suggested capacitors needed per IGBT pair?
Any pointers in the right direction is appreciated.
Show Less
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/IGBT/FS3L40R07W2H5F-B11%E4%B8%AD%E7%9A%84%E7%83%AD%E6%95%8F%E7%94%B5%E9%98%BB%E7%9A%84%E5%9C%B0%E5%92%8C%E5%8A%9F%E7%8E%87%E9%83%A8%E5%88%86M1%E4%B8%AD%E7%9A%84%E5%9C%B0%E5%8F%AF%E4%BB%A5%E4%B8%8D%E5%90%8C%E5%90%97/td-p/744301
Show LessThis is in regards to 1ED3124MC12H trying to drive IGBT model FZ900R12KP4HOSA1.
All my questions below are in regards to the gate driver.
1. For the IN+ and IN-, I assume that I would need to use a PWM signal to turn on the IGBT? If so, what are the voltage and also the duty cycle percentage parameters for the PWM signal to turn on the IGBT?
2a. IN+ is a non-inverted control signal, and IN- is an inverted control signal. Does this mean IN+ turns ON the IGBT and IN- turns OFF the IGBT?
2b. If yes, does this mean I must send an inverted PWM signal in order to turn off the IGBT after I turned it on?
3. Does IN+ connect to the positive (+) of the PWM module and IN- connect to the negative (-) of the PWM module?
4. Based upon page 8, Figure 6, correct me if I'm wrong but it seems we need 3 voltage supplies?
a. A +3.3V from VCC1 to GND1 (with a 100nF capacitor in-between)
b. A +15V from VCC2 to an independent branch (with a 4 microfarad capacitor in-between)
c. A -8V from the independent branch to VEE2 (with a 4 microfarad capacitor in-between)
5. Is SGND simply the ground for VCC1, separated by a 100nF capacitor? The reason I'm asking is because I've never seen the term "SGND". I'm not sure what the "S" means in "SGND".
Show LessHey guys, the following topology is a DC/AC application, inverter mode simulation, can I use this topology for rectifier mode simulation? How do I parameterize it? Thanks!
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/IGBT/%E5%8A%9F%E7%8E%87%E4%BB%BF%E7%9C%9F/td-p/743892
Show LessHi
May I know IKCM30F60GD , what is the max output current @80 C.
Thanks
您好:
现在我们在用贵公司的1ED020I12-F2芯片,但是出现了一个问题,在使用数据手册基本电路图的前提下,该芯片的OUT引脚一直输出低电平,此时/FLT也是低电平。后测量后发现DESAT引脚上有大约0.7V的电压,然后我们给了DESAT一个低电平,此时输出是正常的,/FLT也是高电平,即正常工作。所以请问为什么正常使用DESAT引脚上会有一个0.7左右的电压,而该电压又会导致/FLT输出低电平,导致OUT输出也是低电平?
Show Less