Motor Control ICs Forum Discussions

Hello community!

At our company we have a very interesting and complex problem with IMC101 microcontrollers. This controller is integrated in multiple boards that we use for our products and since launch of our products we have received multiple claims from our customers of boards not working.

After investigation we have concluded that in some cases motor parameters had been corrupted and in some cases, scripting was corrupted on the field.

Because we can make the product OK again by just reuploading the motor parameters file in some cases and reuploading just scripting file in other cases. It does not seem to be a safety function problem, while I can connect to the device using iMOTIONconfig.exe to the claimed products with corrupted scripting, just for a second before device fails.

Some information regarding our setup:

• IMC101
• Firmware version 1.3.3
• Safety is enabled
• We use User Mode UART but only to update the speed (no motor parameters are updated)
• Products work fine for a couple of months then we get the claim

I would appreciate any insight into this problem or if anyone else has similar experience es to what could be the problem.

 

Regards,

Jure

Show Less

 

Good morning all,

I got an issue when I try to flash with iMotion Solution designer and IMotion link , two IMC302 on three prototypes, one is working.

- My 5V00 is perfect with decoupling capacitors for each power pins, tested also with a laboratory power supply & iMotion link  (3V3 out)

- Tested with strong pull up 3K, added on RX, TX pin

 

With Salaea analyser I can recordered this :

@57600 Bauds

Imotion Link -> 0x00, 0x93       Answer : 0xA2, 0x00, 0x67             0xA2 + PDIV

Imotion Link -> 0x00, 0xAA      Answer : 0xF0                                     PDIV + OK

@1000000 Bauds

Imotion Link -> 0xA0, 0X20, 0x00, 0x00, 0x82                  Answer : 0x90

Imotion Link -> 0xA0, 0x00, 0x00, 0x01..............0x73  Answer : 0x90, 0x00

Imotion Link -> 0xA0, 0X20, 0x00, 0x00, 0x82                 Answer : 0x20

Imotion Link -> 0x47, 0x2C, 0x0F, 0x7C..............0x73  Answer : 0x69, 0x82

And now IMotion Solution Designer says : Error while programming.

 

 

I would like also some support to programm the IMC302A with Segger trough SWD, I can connect, I can erase the uC, but what is the way to program the output files : IMC302A-F048_A_V5.02.00.ldf & out.ldf ?, the segger tools whant to have a .bin or a .hex file.

It is a very important project for me and my compagny, could you give me more information what could arrive ?

In advance thanks a lot for your support and help.

Best regards

Show Less

Hi guys, I use the new iMOTION solution design, but before I've used the old MCE designer and wizard to program my motors and fans. Recently I want to move to the new application iMOTION. I config the wizard first, build the program, connect and programming my fan. Then I go to dashboard and verify if my parameters are correct. In this moment my problems begin: if I don't increase Vd and Vq the fan never moves, but even the application tell me that this two are variable that are not saved in my wizard, so how can I run my fan without entering the dashboard? Plus, in the old MCE designer when I finish to programming my board and detach my infineon, the board works on it's own. So, what's the metter with the new application? I'm missing something? I have to do something after the programmer?

Thanks in advice

Show Less

Hi

Im looking at the example projects for IMC 301  F064, ADC example is giving me the error.

************************

No Algorithm found for: 00008000H - 00008A0FH
No Algorithm found for: 2000000CH - 2000014FH
Programming skipped!
Error: Flash Download failed - "Cortex-M0"
Flash Load finished at 13:09:17

*******************

I have the right algorithms as they were verified by CCUTimer example, could anyone throw some light on this concern?

Show Less

Hi @SarkarSushru @SarkarSushru 

 

Thanks for reply "how to program imc102T-F064 with FlashPro – iMOTION (X2S) relates from Elprotronic company "

I used iMOTION_SD_V5.03.07.sdpack 

 This programmer is (FlashPro–iMOTION(X2S)) compatible with  SD_V5.03.07.sdpack ?

 

 

 

.

Show Less

Hello! May I ask if there is any graphical programming software available for the TLE9562-3QX chip? Because I want the CPU to communicate with the TLE9562-3QX chip through SPI to control the motor operation, but I don't know how to write the initialization TLE9562-3QX code and driver code! So I would like to ask if you can tell me how to quickly write TLE9562-3QX initialization and driver code? Thank you! Show Less

My uc is TC367,and Tle9183 communicates with it through SPI. I read the SPI STATUS FLAG ,and the data is 0x06.and we know,spi status flag has 5 bit,so 0x06 means "config valid" and "warning".

my question is how to locate the specific warning info? 

ps:  i have checked values of the registers from 0x40 to 0x4D,but no warings been found.

Show Less