Other Technologies General Forum Discussions
Hello! I want a development board for TDA5230/TDA5231! Do you have PCB board diagrams and component models? Or there are development boards for sale! Also, what is the connection between the development board and the computer host! Where do I get the devices that connect to the computer from?
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/%E5%85%B6%E4%BB%96%E9%80%9A%E7%94%A8%E6%8A%80%E6%9C%AF/Is-there-a-TDA5230-TDA5231-development-board-available/td-p/718747
Show LessPlease provide the following information for part number 11DQ06 and 11DQ10 manufactured by International Rectifier ( which was acquired by Infineon). If a part is obsolete/EOL, please provide its Product Discontinuance/Termination Notice and its replacement. Please email me your response at eric.pomar@copeland.com
1.) 11DQ06
Product Status (e.g., Active, Obsolete, Not Recommended for New Design, etc):
RoHS Compliant(Y/N):
RoHS Exemptions (e.g., 7a, 7c-I, None, etc)?:
Contains SVHC as per REACH ( Y/N):
SVHC Exceeds Threshold Limit as per REACH? ( Y/N/NA)
1.) 11DQ10
Product Status (e.g., Active, Obsolete, Not Recommended for New Design, etc):
RoHS Compliant(Y/N):
RoHS Exemptions (e.g., 7a, 7c-I, None, etc)?:
Contains SVHC as per REACH ( Y/N):
SVHC Exceeds Threshold Limit as per REACH? ( Y/N/NA)
Project Details | |||
Project Name | XWEB1000D | ||
Application | Monitoring | ||
Project Status | Existing Product | ||
Design Location | Copeland Controls, Alpago (BL) Italy | ||
Contract Manufacturer and Location |
In-house: Copeland Controls, Alpago (BL) Italy |
||
Mass Production Date | TBD |
Hi Infineon
We find ESD900/ESD950/ESD901/ESD903/ESD921~3/ESD161 for RF antenna application in Infineon ESD protection as attached file , But We can't find them in Infineon website, can you tell us how to find them, Thanks!!
Show Less
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/%E5%85%B6%E4%BB%96%E9%80%9A%E7%94%A8%E6%8A%80%E6%9C%AF/%E9%9A%94%E7%A6%BB-5v-3-3v-%E8%80%90%E5%8E%8B60v-%E9%98%B2%E7%88%86-CAN-%E6%96%B9%E6%A1%88%E6%8E%A8%E8%8D%90/td-p/715667
Show LessI have loaded the sketch "bldc_shield_blinky_test" and it looks like the shield cannot be found. I have tried two different Arduino Unos as well with the same result.
When I open the serial monitor I get:
INFO: Starting initialization
INFO: Sending reset request to all boards
WARNING: Board[1]; Command[901]; Answer[0]
WARNING: Board[1]; Command[901]; Answer[0]
WARNING: Board[1]; Command[901]; Answer[0]
Here is a pic of the unit. LED2 lights up white when 12VDC is supplied to the shield.
Can anyone provide me with some next steps or troubleshooting?
Show Less
Is any possibility, to detect RX transceiver on a E1 multiframe structure channel shifted? and if so, is someway to synchronize TX according to channel shifted?
For example, in a E1 32-channel frame, channel 00 is the synchronization, but there is a particular system that synchronization channel is assigned to channel 01.
Many thanks.
Show LessPlease provide MSL Level for the above part if Applicable.
Regards
Hema
I want to configure the TLE9561's specific frame wake-up configuration. After following the steps below to configure the TLE9561, the phenomenon is still waking up at any frame after hibernation:
I want to configure the specific frame wake-up configuration of the TLE9561. After following the steps below before being downed, the Phenomenon is still that any frame can wake up after hibernation:
In normal mode The initial state is CAN normal mode
Detected that the ignition switch enters power down mode and starts configuring the CAN specific frame to wake up (Detected that the ignition switch has begun the power-down mode and started to configure the CAN specific frame to wake up)
The specific steps are as follows: The specific steps are as follows:
Write 0x0 to BUS_CTRL;
Write 0x0 to SWK_CDR_CTRL;
Write 0xCC40 to SWK_BTL1_CTRL ; //For SWK_BTL1_CTRL values, please refer to table 82 in the manual
Write 0xA898 to SWK_CDR_LIMIT; //SWK_CDR_LIMIT values refer to manual table 82
Write 0x5 to SWK_CDR_CTRL;
Write 0x49 to SWK_ID0_CTRL;
Write 0xFF7C to SWK_MASK_ID0_CTRL;
Write 0xFFFF to SWK_MASK_ID1_CTRL;
Write 0x8 to SWK_DLC_CTRL;
Write 0x0 to SWK_DATAX_CTRL;
Write 0x0 to BUS_CTRL;
Read SWK_STAT;
Write 0x1 to SWK_CTRL;
Read BUS_STAT;
Write 0x5 to BUS_CTRL_0;
Read WK_STAT;
enter sleep mode (into sleep mode)
I would like to ask if there are any specific bits that can prove that I have activated the option to wake up, or can it give me the correct configuration experience
I would like to ask if there is a specific potential energy that affects that I have activated the option to wake up, or if you can provide me with the correct configuration experience.
smartconx_target@Q!w2e3r4t5y6u7i8o9p0||/t5/%E7%94%B5%E6%BA%90%E7%AE%A1%E7%90%86%E8%8A%AF%E7%89%87/TLE9561-3QX%E6%9C%89%E5%85%B3CAN%E7%89%B9%E5%AE%9A%E5%B8%A7%E5%94%A4%E9%86%92%E7%9A%84%E9%97%AE%E9%A2%98-Problems-related-to-CAN-specific-frame-wake-up-in/td-p/667094
Show LessHi, I have ordered CY8C9520A for 20 bit IO Expander,
The problem is that I can't find anything in the datasheet for basic circuit setup and testing.
Please advise.
Thanks
Clement
Show Less