infineon4engi@twitter twitter

infineon4engineers Facebook

infineon@linkedin linkedin

infineon@youtube youtube

+ Post New Thread
Page 1 of 11 1 2 3 4 5 ... LastLast
Threads 1 to 20 of 205

Forum: General Forum

General Forum

  1. DPS310 Evaluation Kit (EVAL SHNBV01) pinout

    I have the evaluation kit of DPS310 (EVAL SHNBV01) which comes with the BLE module. It works with the Infenion mobile app very well. My question...

    Started by tharindusuraj‎, Yesterday 11:12 PM
    dps310, eval shnbv01, pressure sensor
    • Replies: 0
    • Views: 13
    Yesterday, 11:12 PM Go to last post
  2. Using Infineon TLE493D-A2B6 with Teensy 3.2 (or arduino)

    I am using (or attempting to use) a teensy 3.2 using the Arduino IDE to interact with a 3-axis hall effects sensor (the Infineon TLE493D-A2B6). The...

    Started by Adam Metcalf‎, Oct 30th, 2019 08:35 AM
    arduino, teensy 3.2, tle493d-a2b6
    • Replies: 1
    • Views: 513
    Oct 31st, 2019, 01:41 AM Go to last post
  3. IFX91041EJ V50 VS Pin Connectivity

    I'm using IFX91041EJ V50 to generate +5VDC in my project. On Page No.13 in section 8.4 IFX91041EJV50, IFX91041EJV33 with fixed Output Voltage : ...

    Started by Dark Sorrow‎, Oct 23rd, 2019 01:20 AM
    • Replies: 0
    • Views: 329
    Oct 23rd, 2019, 01:20 AM Go to last post
  4. Complement sensing Mode of DFLASH

    Hello, I will get reset when I tried to read the erased DFLASH which is in complement sensing mode.Any solution for this?

    Started by gurugiri‎, Sep 27th, 2019 10:21 AM
    complement sensing mode
    • Replies: 1
    • Views: 919
    Sep 30th, 2019, 12:03 AM Go to last post
  5. TLE7242 dither waveform problem

    Hi all, I can set and see differences betwen old and new setpoint value, KP/KI value, Main Freq, But, when I set dither value (Msg#3, Msg#4), and...

    Started by rtoprak‎, May 29th, 2019 07:07 AM
    • Replies: 1
    • Views: 10,833
    Aug 30th, 2019, 03:50 AM Go to last post
  6. Position2GO - Serial Output

    Sample UI I want to built a custom UI for the demo board POSITION2GO. The interface will be like a military radar. I want to fetch the demo board...

    Started by ruhul8357‎, Jul 31st, 2019 01:41 PM
    • Replies: 4
    • Views: 2,641
    Aug 28th, 2019, 05:57 PM Go to last post
  7. IRPS5401 soft OFF using PMBUS command?

    Hi. Has anyone had any luck getting a bunch of channels on the IRPS5401 to sequence off (aka soft off) in response to a PMBUS command? I've setup...

    Started by jeffwc1973‎, Aug 5th, 2019 06:05 PM
    irps5401, pmbus
    • Replies: 1
    • Views: 865
    Aug 28th, 2019, 03:12 PM Go to last post
  8. DPS422 Pin 1 Marking Dot

    Dear Sir/Madam, It's my first time posting on the forum so I'm not really sure if my post is in the right box. Please help me moving the thread to...

    Started by tran_dang0709‎, Aug 21st, 2019 01:19 AM
    • Replies: 1
    • Views: 1,097
    Aug 21st, 2019, 07:15 PM Go to last post
  9. [Position2Go] Frame interval vs time measured through ComLib interface

    I set up my position2go to capture 128 points at 300 kHz sampling frequency in Doppler mode. This means 1 chirp (not really a chirp because doppler)...

    Started by agallenSMX‎, Aug 15th, 2019 04:05 PM
    • Replies: 0
    • Views: 853
    Aug 15th, 2019, 04:05 PM Go to last post
  10. DPS422 reference value for raw temperature and pressure measurement

    I'm using the DPS422 via i2C but not getting the correct temperature und pressure. Maybe I'm calculating wrong, but I can't find anything wrong in...

    Started by ludw‎, Aug 8th, 2019 07:11 AM
    dps 422, dps422, iot
    • Replies: 0
    • Views: 2,868
    Aug 8th, 2019, 07:11 AM Go to last post
  11. BGT24LTR11 tangential signal sensitivity (TSS) calculation

    How can I evaluate this device as a detector? The most useful parameter is TSS, but it's calculation involves parameters such RF bandwidth, video...

    Started by unnabi‎, Jul 31st, 2019 05:20 PM
    • Replies: 0
    • Views: 1,101
    Jul 31st, 2019, 05:20 PM Go to last post
  12. tlv493d reading problem

    I read data from tlv493 via i2c bus with xilinx fpga spartan6. the setting procedure is: for low power mode: 1. write data (0x00 0x80 0x00 0x60)...

    Started by matthewli‎, Jul 29th, 2019 08:23 PM
    • Replies: 1
    • Views: 939
    Jul 30th, 2019, 03:15 AM Go to last post
  13. Distance2Go - Change FMCW Direction & Min RF Frequency

    Hi, I'm very new to D2G. Can anyone help/guide me on (1) to change FMCW chirp direction - currently 'up chirp only'. I would like to test on...

    Started by suraya225‎, Jul 12th, 2019 04:32 PM
    • Replies: 3
    • Views: 1,840
    Jul 23rd, 2019, 07:53 AM Go to last post
  14. TLE493D-W2B6-A0 - Reading 0xFF in all registers

    I am using STM32F303x microcontroller to established the communication with the TLE493D-W2B6 A0. I made the reset commands as said in the manual...

    Started by Syncmaster‎, Jul 22nd, 2019 12:19 AM
    • Replies: 2
    • Views: 915
    Jul 22nd, 2019, 07:07 AM Go to last post

    Hello, I am working with the EVAL BGT24LTR11 BOARD. It works fine in Doppler mode but I am noticing some problems when configured to FMCW mode. I...

    Started by emacar‎, May 29th, 2019 05:17 AM
    eval bgt24ltr11 board, fmcw, radar, radar 24ghz, radar24ghz
    • Replies: 4
    • Views: 2,349
    Jun 17th, 2019, 01:32 AM Go to last post
  16. BGT24LTR11 maching structures

    What's the BGT24LTR11N16's output impedance on TX and RX ports? It does not specify numerical value anywhere in datasheets, only specify matching...

    Started by unnabi‎, Apr 22nd, 2019 10:55 AM
    • Replies: 2
    • Views: 1,695
    Jun 14th, 2019, 10:17 PM Go to last post
  17. Porting Open-Source-Software-Stack for TPM 2.0

    Hello, an article on the Infineon website announced that there is an Open-Source-Software Stack for the development of TPM 2.0 based embedded...

    Started by jan0385‎, May 27th, 2019 01:36 AM
    • Replies: 1
    • Views: 1,104
    Jun 11th, 2019, 06:49 AM Go to last post
  18. Optiga TrustX key derivation

    Hi, I am playing this example from NordicSemi here:...

    Started by ozanoner‎, Jun 6th, 2019 07:49 AM
    key derivation
    • Replies: 0
    • Views: 1,012
    Jun 6th, 2019, 07:49 AM Go to last post

    Is it possible to configure the HYBRID KIT DRIVE SENSE evaluation kit to work with a PMDC motor? Ideally with resolver feedback? Any pointers...

    Started by lightning_young‎, May 31st, 2019 08:24 AM
    hybrid kit drive sense
    • Replies: 0
    • Views: 1,073
    May 31st, 2019, 08:24 AM Go to last post
  20. Optiga Trust X vs 802.1AR

    Hi, I am planning to use Optiga TrustX module in my project. One requirement in that project is to comply with the 802.1AR standard (Secure Identity...

    Started by ozanoner‎, May 21st, 2019 10:10 AM
    802.1ar, optiga trust x
    • Replies: 0
    • Views: 1,192
    May 21st, 2019, 10:10 AM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

All content and materials on this site are provided “as is“. Infineon makes no warranties or representations with regard to this content and these materials of any kind, whether express or implied, including without limitation, warranties or representations of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, whether express or implied, is granted by Infineon. Use of the information on this site may require a license from a third party, or a license from Infineon.

Infineon accepts no liability for the content and materials on this site being accurate, complete or up- to-date or for the contents of external links. Infineon distances itself expressly from the contents of the linked pages, over the structure of which Infineon has no control.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Usage Terms of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Usage Terms of this site. Infineon reserves the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.